-
The Winson WCS1600 current sensor provides economical and precise solution for both DC and AC current sensing in industrial, commercial and communications systems. The unique package provides easy implementation without breaking original system and makes current sensing possible. Typical applications include motor control, load detection and management, over-current fault detection and any intelligent power management system etc. -
MF RC522 is a highly integrated read and write card chip applied to the 13.56MHz contactless communication.It is a low-voltage, low-cost, and small-sized non-contact card chip, a best choice for intelligent instrument and portable handheld devices. The MF RC522 uses advanced modulation and demodulation concept which fully presented in all types of 13.56MHz passive contactless communication methods and protocols. In addition, it supports rapid CRYPTO1 encryption algorithm to verify MIFARE products. MFRC522 also supports MIFARE series of high-speed non-contact communication, with a two-way data transmission rate of up to 424kbit/s. As a new member of the 13.56MHz highly integrated reader card series, MF RC522 is much similar to the existing MF RC500 and MF RC530 when there are also great differences. It communicates with the host machine via the serial manner which needs less wiring. You can choose between SPI, I2C and serial UART mode (similar to RS232), which helps reduce the connection, save PCB board space (smaller size), and reduce cost. -
The MB102 is a breadboard power supply module manufactured by the YuRobot . This module has the marking 545043 and MB V2 on the printed circuit board (PCB). It provides dual 5 V and 3.3 V power rails, and has a multi-purpose female USB socket. -
CH340 is a USB bus convert chip and it can realize USB convert to serial interface, USB convert to IrDA infrared or USB convert to printer interface. In serial interface mode, CH340 supplies common MODEM liaison signal, used to enlarge asynchronous serial interface of computer or upgrade the common serial device to USB bus directly. More detail about USB convert to printer interface please referring to the second manual CH340DS2. In infrared mode, add infrared transceiver to CH340 can compose USB infrared adapter, realize SIR infrared communication. -
CAN-BUS is a common industrial bus because of its long travel distance, medium communication speed and high reliability. It is commonly found on modern machine tools and as an automotive diagnostic bus. This CAN-BUS Shield adopts MCP2515 CAN Bus controller with SPI interface and MCP2551CAN transceiver to give your Arduino/Seeeduino CAN-BUS capability. With an OBD-IIconverter cable added on and the OBD-II library imported, you are ready to build an onboard diagnostic device or data logger. -
Description: -Mini PFM Control. -On-board input voltage indicator. -High conversion efficiency, maximum to 96%. -Any DC voltage input 0.9V ~ 5V, output 5V DC voltage can be stable, with two AA batteries input to the output current of 500-600MA, single AA battery power supply output current about 200MA. -On-board USB female, can supply power directly to the USB interface. -Small dimension. -
The SIM900 is a complete Quad-band GSM/GPRS solution in a SMT module which can be embedded in the customer applications. Featuring an industry-standard interface, the SIM900 delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. With a tiny configuration of 24mm x 24mm x 3 mm, SIM900 can fit almost all the space requirements in your M2M application, especially for slim and compact demand of design. -
DescriptionThis is a speed sensor, the major goal is to check the rate of motor.It was widely used in motor speed detection, pulse count, the position limit, etc.Features:-Groove type optical coupling sensor-The output state light, lamp output level, the output low level light.-Covered, output high level;Without sunscreen, the output low level.-The comparator output signal is clean, good waveform, driving ability is strong, for more than 15 ma.-It has a fixed bolt hole, convenient installation. -
Inputs
- GND – This is where you connect the low side of the voltage you are measuring. Caution! : This is the same electrical point as your Arduino ground.
- VCC: The is where you connect the high side of the voltage you are measuring
Outputs
- S: This connects to your Arduino analog input.
- – (or minus): This connects to your Arduino ground.
- : This is not connected. It does absolutely nothing.
-
The nRF24L01 is used on a wide variety of applications that require wireless control. They are transceivers which this means that each module can transmit and receive data. These modules are very cheap and you can use them with any microcontroller (MCU). Specifications nRF24L01 – 2.4GHz RF Transceiver- Low cost single-chip 2.4GHz GFSK RF transceiver IC
- Range with Antenna: 250Kb rate (Open area) >1000 meter
- Power: Ultra low power consumption
- Input Voltage: 3.3V
- Pins: 5V tolerant
-
Description: -Color: red. -Main chip: LM393. -Operating voltage: DC 5V. -Light weight design. -With single channel signal output. -Low level output signal used for human body touch sensor alarm. -Compatible with Arduino. -
P/N: Door lock solenoid NC-0837L-12V Materials: Copper lines, Matal, Cable Related Voltage: 12V/ DC Stroke VS Force 50grams @ 10mm Power 8 wattages Mounting hole: 6.8*3mm/0.26"*0.12"(L*W) Insulation Resistance: 100M Ohms, 500V DC Dielectric Voltage 700V DC per seconds Life cycle 1,000,000 cycle min Color Silver -
HX711 is a precision 24-bit analog to-digital converter (ADC) designed for weigh scales and industrial control applications to interface directly with a bridge sensor. The input multiplexer selects either Channel A or B differential input to the low-noise programmable gain amplifier (PGA). Channel A can be programmed with a gain of 128 or 64, corresponding to a full-scale differential input voltage of ±20mV or ±40mV respectively, when a 5V supply is connected to AVDD analog power supply pin. Channel B has a fixed gain of 32.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
