-
Bee Adapter is a compact USB to serial adapter equipped with BEE (20pin 2.0mm) sockets. With integrated FT232RL IC, It can be used for programming or communicating with board which basic Arduino but without USB interface,like Sniffer Nano. On the other hand, you may connect your PC to various wireless applications via the BEE compatible modules. The adapter also support XBee module interface.
-
This is the XBee XBP24-BZ7WIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. Series 2B modules use a different hardware configuration from the earlier models and while they will communicate with Series 2 XBee modules, they are not compatible with the outdated Series 2.5 Modules.
-
The Winson WCS1600 current sensor provides economical and precise solution for both DC and AC current sensing in industrial, commercial and communications systems. The unique package provides easy implementation without breaking original system and makes current sensing possible. Typical applications include motor control, load detection and management, over-current fault detection and any intelligent power management system etc.
-
Water sensor brick is designed for water detection, which can be widely used in sensing rainfall, water level, and even liquid leakage. Water Detector / Sensor Connecting a water sensor to an Arduino is a great way to detect a leak, spill, flood, rain, etc. It can be used to detect the presence, the level, the volume and/or the absence of water. While this could be used to remind you to water your plants, there is a better Grove sensor for that. The sensor has an array of exposed traces, which read LOW when water is detected.
-
W5500 Ethernet shield is designed using the WIZnet W5500 chip. It supports both 3.3V & 5V. This Ethernet Shield is compatible with Arduino and ARM embed Platform. Features -Suppport 3.3V / 5V. -High Speed Ethernet controller W5500 chip. -SPI interface. -Internal 32Kbytes Tx/Rx buffer. -10/100 Ethernet PHY embedded. -Support Auto Negotiation (Full / Half duplex, 10 / 100-based). -Hardwired TCP/IP Protocols : TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE. -User Selectable GPIO pin. -Support SD-card slot for storage. -Support I2C, UART interface.
-
VS1003 is an MP3 module with on-board microphone, it supports audio decoding formats of MP3, MP3 V, WMA, WAV, MIDI and the SP-MIDI.
Features
- Separate analog, digital and IO power supply; serial data and control interface (SPI).
- 1 headphones and audio output interface, the internal PLL clock frequency multiplier; high-quality stereo DAC, 16-bit adjustable-chip ADC, high-quality stereo earplugs drive (30 EURO)
- A microphone for recording, support for recording encoding format: IMA ADPCM (monaural).
- 1 ine_in input interface supports two input methods; supports MP3 and WAV streams.
- Separate analog, digital and IO power supply
- On-board 3.3V and 2.5V LDO chip AMS-1117, the largest current provide of 800mA.
- Single power supply: 5 VDC, capacitor filter.
- 12.288 MHz crystal.
-
Inputs
- GND – This is where you connect the low side of the voltage you are measuring. Caution! : This is the same electrical point as your Arduino ground.
- VCC: The is where you connect the high side of the voltage you are measuring
Outputs
- S: This connects to your Arduino analog input.
- – (or minus): This connects to your Arduino ground.
- : This is not connected. It does absolutely nothing.