-
ESP-12E WiFi module is developed by Ai-thinker Team. core processor ESP8266 in smaller sizes of the module encapsulates Tensilica L106 integrates industry-leading ultra low power 32-bit MCU micro, with the 16-bit short mode, Clock speed support 80 MHz, 160 MHz, supports the RTOS, integrated Wi-Fi MAC/BB/RF/PA/LNA, on-board antenna. The module supports standard IEEE802.11 b/g/n agreement, complete TCP/IP protocol stack. Users can use the add modules to an existing device networking, or building a separate network controller. ESP8266 is high integration wireless SOCs, designed for space and power constrained mobile platform designers. It provides unsurpassed ability to embed Wi-Fi capabilities within other systems, or to function as a standalone application, with the lowest cost, and minimal space requirement.
-
MQ-135 is sensitive air quality sensor that detects NH3, NOx, alcohol, benzene, smoke, CO2, etc. Heater voltage 5V, 31 ohm (40mA consumption) The board has digital and analog output.
FEATURES
- Detects NH3, NOx, alcohol, benzene, smoke, CO2, etc.
- Operating voltage 5V
- Operating current 40mA
- Both digital and analog output
- Popular sensor - a lot of examples available for different platforms
- Port explanation : AO for analog output, DO for digital output, GND for ground, VCC for 5V voltage input
-
Specifications Modulation: Digital Torque: 4.8V: 130.54 oz-in (9.40 kg-cm) 6.0V: 152.76 oz-in (11.00 kg-cm) Speed: 4.8V: 0.20 sec/60° 6.0V: 0.16 sec/60° Weight: 1.94 oz (55.0 g) Dimensions: Length:1.60 in (40.7 mm) Width:0.78 in (19.7 mm) Height:1.69 in (42.9 mm) Gear Type: Metal Pulse Cycle: 1 ms Connector Type: JR
-
The module (MicroSD Card Adapter) is a Micro SD card reader module, through the file system and the SPI interface driver, MCU to complete the file system to read and write MicroSD card. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write.
-
Highlights: By adjusting the potentiometer can set the length of time. MicroUSB 5.0V power supply with an input port, easy to use. 5 ~ 30V wide supply voltage. External signaltrigger and keytriggerin two ways. With a relay indicator. Anti-interference ability, the relay at various interference will not misoperation, suitable for industrial control.
-
This module allows you to detect when sound has exceeded a set point you select. Sound is detected via a microphone and fed into an LM393 op amp. The sound level set point is adjusted via an on board potentiometer. When the sound level exceeds the set point, an LED on the module is illuminated and the output is sent low.
-
This module integrates DHT11 sensor and other required components on a small PCB. The DHT11 sensor includes a resistive-type humidity measurement component, an NTC temperature measurement component and a high-performance 8-bit micro controller inside, and provides calibrated digital signal output. It has high reliability and excellent long-term stability, thanks to the exclusive digital signal acquisition technique and temperature & humidity sensing technology.
-
200grm Straight Bar Mini Load Cell RSN-157 Weight Capacity Max - 200 g Maximum Overload - 220 g Cell Repeatability Error Max - ± 50 mg Cell Non-Linearity Max - 50 mg Cell Hysteresis Max - 50 mg Electrical Properties Rated Output - 600 μV/V Rated Output Error Max ± 150 μV/V Output Impedance 1 kΩ Creep 100 mg/hr Temperature Effect on Zero 5 mg/°C Temperature Effect on Span 5 mg/°C Supply Voltage Min 3 V DC Supply Voltage Max 10 V DC Zero Balance Ratio ± 100 μV/V Material - Aluminium Alloy (LY12CZ) Screw Thread Size - 2.5M 47mm x 12mm x 6mm, 110mm Wire
-
Raspberry Pi 5 Model 8GB E-890 2.4GHz quad-core, 64-bit Arm Cortex-A76 CPU, with 512KB L2 caches and a 2MB shared L3 cache Video Core VII GPU LPDDR4X-4267 8GB SDRAM 2.4 GHz and 5.0 GHz 802.11ac Wi-Fi. Bluetooth 5.0 / Bluetooth Low Energy (BLE) Micro SD card slot, with support for high-speed SDR104 mode 2 USB 3.0 ports, supporting simultaneous 5Gbps operation 2 USB 2.0 ports Gigabit Ethernet, with PoE+ support (requires PoE+ HAT) 2 4 lane MIPI camera/display transceivers PCIe 2.0 x1 interface for fast peripherals 5V/5A DC power (PD enabled) Raspberry Pi standard 40-pin header Real-Time Clock (RTC), powered by an external battery On-board power button!!