-
The Raspberry Pi Camera Module v2 is a high quality 5 megapixel designed add-on board for Raspberry Pi, featuring a fixed focus lens. -
This is a simple-to-use, UART controlled, color camera with on-board JPEG compression. Capable of resolutions up to 640x480, and a number of color types. Send the snapshot command, and this module will capture a single-frame picture, compress it, and send it back over a serial connection. -
The OV7670 is a low cost image sensor DSP that can operate at a maximum of 30 fps and 640 x 480 ("VGA") resolutions, equivalent to 0.3 Megapixels. The captured image can be pre-processed by the DSP before sending it out. This preprocessing can be configured via the Serial Camera Control Bus (SCCB). -
This is a small but very effective Linear current sensor module, This module is designed around ACS712 hall effect based current sensor chip. This module is good for max 5A current measurement. ACS712 chip takes AC or DC voltage at its input and its output varies linearly with sensed current, its output is analog voltage. -
An electronic speed control or ESC is an electronic circuit with the purpose to vary an electric motor's speed, its direction and possibly also to act as a dynamic brake. -
This is a breakout board for the fully integrated Hall Effect based linear ACS712 current sensor. The sensor gives precise current measurement for both AC and DC signals. Thick copper conductor and signal traces allows for survival of the device up to 5 times overcurrent conditions. The ACS712 outputs an analog voltage output signal that varies linearly with sensed current. The device requires 5VDC for VCC and a couple of filter capacitors. Please keep in mind that though the ACS712 is rated for 2.1kV isolation, the PCB it is on is not designed for that type of voltage. Please keep that in mind if you are using this breakout in high voltage applications. -
Reading Sensing and Controlling current flow is a requirements in a wide variety of application including, over-current protection circuits, switching mode, battery chargers, power supplies, digital watt meter and programmable current source, etc.. The ACS721 current reading module is based on ACS712 Sensor which can detect AC, DC current signal accurately. The maximum AC / DC can be detected using ACS712 will reach 30 amp and present current signal can read via analog IO port of Arduino, Product available for this module are 30A, 20A, 5A. for this demonstration we will used the ACS712 30A. -
Sensitive material of MQ-3 gas sensor is SnO2, which with lower conductivity in clean air. When the target alcohol gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration. MQ-3 gas sensor has high sensitity to Alcohol, and has good resistance to disturb of gasoline, smoke and vapor. The sensor could be used to detect alcohol with different concentration, it is with low cost and suitable for different application. -
Sensitive material of MQ-2 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensor’s conductivity is more higher along with the gas concentration rising. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration. MQ-2 gas sensor has high sensitity to LPG, Propane and Hydrogen, also could be used to Methane and other combustible steam, it is with low cost and suitable for different application. -
The sensor has a sensitive filament made of SnO2. In the presence of clean air, this filament tends to have lower electrical conductivity. When a combustible gas such as LPG is introduced, the filament’s conductivity rises, and the amount of change in it’s conductance/resistance can be used to indicate the equivalent gas concentration. This effect tends to be particularly pronounced at higher temperatures, and resistive heating element is present as well. SnO2 is particularly sensitive to Methane, Butane and Propane, but is also sensitive to other combustible gases as well. -
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC. -
This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC. -
Sensitive material of MQ-9 gas sensor is SnO2, which with lower conductivity in clean air. It make detection by method of cycle high and low temperature, and detect CO when low temperature (heated by 1.5V). The sensor’s conductivity is more higher along with the gas concentration rising. When high temperature (heated by 5.0V), it detects Methane, Propane etc combustible gas and cleans the other gases adsorbed under low temperature. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration. MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application. -
The MQ-135 is a hazardous gas sensor used for air quality control and is suitable for detecting NH3 (Ammonia), NOx, alcohol, Benzene, smoke, CO2, etc. -
The MPX2010DP is a differential, dual port silicon pressure sensor in 4 pin SIP package. This piezoresistive pressure sensor provides very accurate and linear voltage output directly proportional to applied pressure. It includes on-chip integrated strain gauge and thin film resistor network. The sensor is laser trimmed for precise span, offset calibration and temperature compensation. -
The MPX2100 series device is a silicon piezoresistive pressure sensor providing a highly accurate and linear voltage output — directly proportional to the applied pressure. The sensor is a single, monolithic silicon diaphragm with the strain gauge and a thin–film resistor network integrated on–chip. The chip is laser trimmed for precise span and offset calibration and temperature compensation. Features • Temperature Compensated Over 0°C to 85°C • Easy–to–Use Chip Carrier Package Options • Available in Absolute, Differential and Gauge Configurations • Ratiometric to Supply Voltage • ±0.25% Linearity (MPX2100D) Application Examples • Pump/Motor Controllers • Robotics • Level Indicators • Medical Diagnostics • Pressure Switching • Barometers • Altimeters -
The MPX5010DP is a dual port, integrated silicon pressure sensor in 6 pin SIP package. This piezoresistive transducer is state of the art monolithic silicon pressure sensor designed for wide range of applications. It is ideally suited for microprocessor or microcontroller based system. This transducer combines advanced micromachining techniques, thin-film metallization and bipolar processing to provide an accurate, high level analogue output signal that is proportional to applied pressure. The axial port has been modified to accommodate industrial grade tubing. >On-chip signal conditioned, temperature compensated and calibrated >Differential configuration >5.0% maximum error over 0°C to 85°C >Durable epoxy unibody >Temperature compensated over -40°C to 125°C >Patented silicon shear stress strain gauge >Pressure range from 0KPa to 10KPa >Supply voltage range from 4.75VDC to 5.25VDC >Sensitivity of 450mV/mm >Response time of 1ms -
Featuring our Ultra Compact Bucket Printer Line – EPM-203 Thermal Printer from APS, integrating printers to your product were never so easy. Offering complete technical support to help you with your design we also undertake customized design solutions. Printer Specifications: 2 Inch, 3 Inch & 4 Inch Operating Voltage: 5V, 12V & 24V Cutter: Optional -
LPC2148 16/32 bit ARM7TDMI-S with 512K Bytes Program Flash, 42KBytes RAM, USB 2.0, RTC, 10 bit ADC 2.44 uS, 2x UARTs, 2x I2C, SPI, 2x 32bitTIMERS, 6x PWM, 8x CCR, 1x DAC, WDT, 5V tolerant I/O, up to 60MHz operation standard JTAG connector with ARM 2x10 pin layout forprogramming/debugging with ARM-JTAG Perfect solution for developing USB peripherials status LED power supply LED power supply filtering capacitor 12 Mhz crystal on socket 32768 Hz crystal and RTC backup battery connector extension headers for all uC ports Extension header for Voltages 3.3v , UART , JTAG and USB D D- -
It is an easily cascadable 8×8 monochromatic LED dot matrix display module with onboard MAXIM’s MAX7219 LED driver chip. The MAX7219 allows you to drive the LED matrix using only three I/O pins of Arduino or any other microcontroller. The LED matrix module used in Easy Matrix has a bigger dot size (5mm) and has the overall display dimensions of 60.2mm x 60.2mm (2.4″x2.4″). It is easily cascadable in series with the help of precisely aligned male and female header pairs located on the left and right sides of the display module. With lots of freely available Arduino libraries for MAX7219 chip, this module is easy to use in any Arduino project for displaying basic text and animation. -
This is a protoboard that stacks on to the Arduino UNO/MEGA – It brings all the data, I/O 5V and Ground pins to the shield and provides a nice surface for soldering your components. Stacking headers are included so you can stack additional shields onto this one. -
The Mega2560 Shield makes it easy for you to design custom circuits. You can solder parts to the prototyping area to create your project, or use it with a small solderless breadboard to quickly test circuit ideas without having to solder. It's got extra connections for all of the Arduino I/O pins, and it's got space to mount through-hole and surface mount integrated circuits. It's a convenient way to make your custom circuit and Arduino into a single module. -
PICkit 2 has a separate programmer/debugger unit which plugs into the board carrying the chip to be programmed, whereas the PICkit 1 was a single unit. This makes it possible to use the programmer with a custom circuit board via an In Circuit Serial Programming (ICSP) header. This feature is not intended[3] for so-called "production" programming, however. The PICkit 2 uses an internal PIC18F2550 with FullSpeed USB. The latest PICkit 2 firmware allows the user to program and debug most of the 8 and 16 bit PICmicro and dsPIC members of the Microchip product line. The PICkit 2 is open to the public, including its hardware schematic, firmware source code (in C language) and application programs (in C# language). End users and third parties can easily modify both the hardware and software for enhanced features. e.g. Linux version of PICkit 2 application software, DOS style CMD support, etc.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
