-
- Can detect flame or wavelength of light source within 760nm~1100nm.
- Lighter flame detect distance 80cm.
- Greater the flame, farther the test distance.
- Detect angle: 60 degree, very sensitive with flame spectrum.
- The sensitivity is adjustable.
-
The DS1990A serial number IButton is a rugged data carrier that serves as an electronic registration number for automatic identification. Data is transferred serially through the 1-Wire protocol, which requires only a single data lead and a ground return. Every DS1990A is factory lasered with a guaranteed unique 64-bit registration number that allows for absolute traceability. The durable stainless-steel iButton package is highly resistant to environmental hazards such as dirt, moisture, and shock. Its compact coin-shaped profile is selfaligning with mating receptacles, allowing the DS1990A to be used easily by human operators. -
A basic 16 button keypad for user input. The buttons are setup in a matrix format. This allows a microcontroller to 'scan' the 8 output pins to see which of the 16 buttons is being pressed.Description
- Weight: 10 grams
- Keypad dimensions: 50mm x 44mm x 1.6mm
- 8-pin 0.1" pitch connector
-
The KY017 is a mercury tilt switch that allows you to detect the tilt of your object so that you can take the appropriate action. It is a nice low cost alternative to a 6 axis accelerometer. When strategically adjusted or situated, it can be very sensitive. The key to using this switch successfully is in understanding the two operational states. -
Just like a joystick on game console. you can control x, y and z dimensions input by this joystick module. It can be considered as combination of potentiometers and one button. Data type of the x, y dimensions are analog input signals and z dimension is digital input signal. thus the x and y ports connect to analog pins of Sensor Shield, while z port connects to digital pin. When using, it can connect with Arduino sensor shield,and connect Arduino corresponding pins through Arduino sensor cables. -
Description: -Color: red. -Main chip: LM393. -Operating voltage: DC 5V. -Light weight design. -With single channel signal output. -Low level output signal used for human body touch sensor alarm. -Compatible with Arduino. -
Highlights:The whole network smallest adjustable boost module can be easily installed in a variety of small equipment.The module supports MicroUSB input,using a USB charger or mobile power supply can easily get the voltage of 9V, 12V, 15V, 18V, 24V.It easy to use.Wide input and output voltage range and high conversion efficiency.Features:1. Maximum output current: 2A (recommended for using within 1A).2.Input voltage: 2 v ~ 24 v.3. Maximum output voltage:> 28 v (recommended for using within 26V).4. Efficiency:> 93%.5. Size: 30mm * 17mm * 14mm (L * W * H). -
Specification: -Voltage: 3.3V. -It's for 8 Pin NRF24L01 Module. -A simple socket board which is for NRF24L01 wireless module. -On-board AMS1117-3.3 chip. -It can be used with NRF24L01 wireless module. -Dimension: 26 x 19 x 12mm. -
In = 2-24V / Out = 5-28V @ 2A Switching Regulator (Boost = Output Voltage has to be higher than input voltage), Good for getting stable 3.3V or 5V output from 1xAA or 2xAA or Li-ion batteries. Specifications: -2V to 24V input voltage with output boost 5V to 28V adjustable. -Maximum output current: 2A. -Input voltage: 2V ~ 24V. -Maximum output voltage: > 5V - 28V. -Efficiency: > 93%. -Input voltage should not exceed the maximum input voltage. -Peak current output current should not more than 2A. -Output voltage should always be higher than Input voltage. -PCB Size: 36 mm * 17 mm * 14 mm. -
Feature: *Operating voltage: 5V. *On-board MAX485 chip. *A low power consumption for the RS-485 communication. *Slew-rate limited transceiver. *5.08mm pitch 2P terminal. *Convenient RS-485 communication wiring. *All pins of chip have been lead to can be controlled through the microcontroller. *Board size: 44 x 14mm. -
Dry reed pipe needs and magnet is used together, in the induction to have certain magnetic, a conducting state, module output low level, no magnetic, is off state, output high level, dry reed pipe and magnetic induction distance within in 1.5 cm beyond insensitive or will not trigger phenomenon. Module DO output end of the single chip microcomputer can I/O port directly connected, through the single chip microcomputer can detect dry reed pipe state trigger. Module DO output end and relay IN end connected to form high power dry reed pipe switch, direct control high voltage.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
