-
Module feature and performance: 5A high-power and high efficiency reduction voltage and low ripple High quality and good performance With power light and voltage display with self-correcting. Adopting advanced voltage microprocessor, and the voltmeter error ±0.1V, measuring range is 0~40V (Note: Please make sure input voltage more than 3.5V to make the voltmeter normal working) Touch the button to change input or output voltage, LED indicator light display is measuring voltage, and can autosave which one voltage, keep pressing the key can turn off the voltmeter Input voltage 4.0～38V (the input voltage must be higher 1.5V than output voltage) Adjustable output voltage range: 1.25V～36V (the input voltage must be higher 1.5V than output voltage) Output power can reach 75W. Output current can reach 5A, suggested use it less than 4.5A (note: Please add a cooling fin into power chip, if you use it with high-power) -
The LilyPad Arduino consists of an ATmega328 with the Arduino bootloader and a minimum number of external components to keep it as small (and as simple) as possible. This board will run from 2V to 5V and offers large pin-out holes that make it easy to sew and connect. Each of these pins, with the exception of ( ) and (-), can control an attached input or output device (like a light, motor, or switch). -
SIM800C is a complete Quad-band GSM/GPRS solution in a SMT type, which can be embedded in the customer applications. SIM800C supports Quad-band 850/900/1800/1900MHz, it can transmit Voice, SMS and data information with low power consumption. With tiny size of 17.6*15.7*2.3mm, it can smoothly fit into slim and compact demands of customer design. -
This module directly connects to any microcontroller UART or through a RS232 converter to PC.It gives UART/Wiegand26 output. This RFID Reader Module works with any 125 KHz RFID tags 1.Specifications 5VDC through USB (External 5V supply will boost range of the module) Current: <50mA Operating Frequency: 125Khz Read Distance: 10cm Size of RFID reader module: 32mm(length) * 32mm(width) * 8mm(height) 2. RS232 interface format: 10 ASCII DATA (card no.) 2 ASCII DATA (XOR result) E.g. Card number is 4500C5D1E9B8 read from reader then the card number on card will be as below. 45 - Preamble 00C5D1E9 value in Hex = 12964329. / B8 is XOR value for (45 XOR 00 XOR C5 XOR D1 XOR E9) Hence number on the card is 0012964329. 1. Data baud rate: 9600 bps 2. Data bit 8 bits 3. Parity check: None 4. Stop bit -
Features
- Supports following Hardwired TCP/IP Protocols : TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
- Supports 8 independent sockets simultaneously
- Supports Power down mode
- Supports Wake on LAN over UDP
- Supports High Speed Serial Peripheral Interface(SPI MODE 0, 3)
- Internal 32Kbytes Memory for Tx/Rx Buffers
- 10BaseT/100BaseTX Ethernet PHY embedded
- Support Auto Negotiation (Full and half duplex, 10 and 100-based)
- Not support IP Fragmentation
- 3.3V operation with 5V I/O signal tolerance
- LED outputs (Full/Half duplex, Link, Speed, Active)
Specifications
- Module size: 55mm x 28mm
- Power supply: 3.3v /5v
- SPI clock frequency(MAX): 80M
- Work current(typ): 128mA
-
The Sound Recorder Module uses the ISD1760 Chip to record and store voice signals. ISD1700 series recording chip is a kind of high integration, high performance chip. This module can be multiple recording, the sampling rate can be set to 6k or 8k by the on-board resistor. There are also some inside sounds to remind the user working state of the module, such as record beginning, record stopping, record erasing , etc. The recording data is stored in the FLASH, without any compression to ensure a good quality. You can easily control this module manually or by Arduino. There are some keys on the module including “REC”,”PLAY”,”EARSE”, you can control the module with these keys. -
SIM800 is a complete Quad-band GSM/GPRS solution in a SMT type which can be embedded in the customer applications.SIM800 support Quad-band 850/900/1800/1900MHz, it can transmit Voice, SMS and data information with low power consumption. With tiny size of 24*24*3mm, it can fit into slim and compact demands of customer design. Featuring Bluetooth and Embedded AT, it allows total cost savings and fast time-to-market for customer applications. -
The AM2302 is a wired version of the DHT22, in a large plastic body. It is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). -
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 10kg/cm (4.8v); 12kg/cm (6v) Operating speed: 0.23sec/60degree (4.8v); 0.2sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6v Temperature range: 0- 55deg Gear Type: Metal gear Dead band width: 1us Power Supply: Through External Adapter servo wire length: 32cm Servo Plug: JR (Fits JR and Futaba) servo arms &screws included and fit with Futaba servo arm It’s universal “S” type connector that fits most receivers.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
