-
Water sensor brick is designed for water detection, which can be widely used in sensing rainfall, water level, and even liquid leakage. Water Detector / Sensor Connecting a water sensor to an Arduino is a great way to detect a leak, spill, flood, rain, etc. It can be used to detect the presence, the level, the volume and/or the absence of water. While this could be used to remind you to water your plants, there is a better Grove sensor for that. The sensor has an array of exposed traces, which read LOW when water is detected. -
Specifications Modulation: Analog Torque: 4.8V: 44.00 oz-in (3.17 kg-cm) 6.0V: 57.00 oz-in (4.10 kg-cm) Speed: 4.8V: 0.23 sec/60° 6.0V: 0.19 sec/60° Weight: 1.31 oz (37.0 g) Dimensions: Length:1.57 in (39.9 mm) Width:0.79 in (20.1 mm) Height:1.42 in (36.1 mm) Gear Type: Plastic Rotation/Support: Bushing Rotational Range: 60° Pulse Cycle: 30 ms Pulse Width: 500-3000 µs Connector Type: J -
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 10kg/cm (4.8v); 12kg/cm (6v) Operating speed: 0.23sec/60degree (4.8v); 0.2sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6v Temperature range: 0- 55deg Gear Type: Metal gear Dead band width: 1us Power Supply: Through External Adapter servo wire length: 32cm Servo Plug: JR (Fits JR and Futaba) servo arms &screws included and fit with Futaba servo arm It’s universal “S” type connector that fits most receivers. -
Specifications • Weight: 55 g • Dimension: 40.7 x 19.7 x 42.9 mm approx. • Stall torque: 9.4 kgf·cm (4.8 V ), 11 kgf·cm (6 V) • Operating speed: 0.17 s/60º (4.8 V), 0.14 s/60º (6 V) • Operating voltage: 4.8 V a 7.2 V • Running Current 500 mA – • Stall Current 2.5 A (6V) • Dead band width: 5 µs • Stable and shock proof double ball bearing design • Temperature range: 0 ºC – 4.8 V a 7.2 V – 900 mA (6V) double ball bearing design 55 ºC -
Tiny and lightweight with high output power. Servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places. It comes with a 3 horns (arms) and hardware. Specifications • Weight: 9 g • Dimension: 22.2 x 11.8 x 31 mm approx. • Stall torque: 1.8 kgf·cm • Operating speed: 0.1 s/60 degree • Operating voltage: 4.8 V (~5V) • Dead band width: 10 µs • Temperature range: 0 ºC – 55 ºC -
This sensor sits in line with your water line and contains a pinwheel sensor to measure how much liquid has moved through it. There's an integrated magnetic hall effect sensor that outputs an electrical pulse with every revolution. The hall effect sensor is sealed from the water pipe and allows the sensor to stay safe and dry. The sensor comes with three wires: red (5-24VDC power), black (ground) and yellow (Hall effect pulse output). By counting the pulses from the output of the sensor, you can easily calculate water flow. Each pulse is approximately 2.25 milliliters. Note this isn't a precision sensor, and the pulse rate does vary a bit depending on the flow rate, fluid pressure and sensor orientation. It will need careful calibration if better than 10% precision is required. However, its great for basic measurement tasks! -
The 28-BYJ48 comes with Breakout using ULN2003 As a Motor driver chip . Rated voltage ： 5VDC Number of Phase 4 Speed Variation Ratio 1/64 Stride Angle 5.625° /64 Frequency 100Hz DC resistance 50Ω±7%(25℃) Idle In-traction Frequency > 600Hz Idle Out-traction Frequency > 1000Hz In-traction Torque >34.3mN.m(120Hz) Self-positioning Torque >34.3mN.m Friction torque 600-1200 gf.cm Pull in torque 300 gf.cm Insulation grade A -
This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm. Features High sensitivity to CH4，Natural gas Small sensitivity to alcohol, smoke Fast response Stable and long life Simple drive circuit -
This IR reflective sensor utilizes a TCRT5000 to detect color and distance. It emits IR and then detects if it receives the echo. This sensor is often used in line following robots, auto data logging on utility meters, because this module can sense if a surface is white or black. The measuring distance range from 1mm to 8mm, and the central point is about 2.5mm. There is also an on-board potentiometer to adjust the sensitivity. The infrared diode will emmitting the infrared continutelly when the module connect to the power, when the emitted infrared light has not been reflected or the strength is not big enough,the triode will in the off state, at this time, D0 output logic LOW and the signal indicate LED off. Application Idea Rainfall detecting Liquid leakage Tank overflow detector Features Supply Voltage: 3.3V~5V Detect distance: 1mm-8mm Digital Outputs HIGH when objects detected On-board indicator LED to show the results On-board potentiometer to adjust the sensitivity On-board LM393 chip -
40KHz Ultrasonic Transducer Transmitter and Receiver Pair. These transducers are very useful in making various sensors for detecting obstacles and measuring distances. Features Use for motion or distance sensing Frequency: 40kHz ±1.0kHz Aluminum case Capacitance: 2000pF ±20% Transmitter: bandwidth 5.0kHz/100dB, sound pressure level 112dB/40 ±1.0kHz Receiver: bandwidth 5.0kHz @ -75dB, min. sensitivity 67dB/40 ±1.0kHz (0dB vs. 1V µbar) R=3.9k. Lead length/spacing: 0.28" Case size: 0.30"H x 0.43" Dia.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
