-
This is the XBee XBP24-BZ7WIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. Series 2B modules use a different hardware configuration from the earlier models and while they will communicate with Series 2 XBee modules, they are not compatible with the outdated Series 2.5 Modules. -
This is a simple to use, USB to serial base unit for the XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach USB cable, and you will have direct access to the serial and programming pins on the XBee unit. The board is powered by the USB cable. XBee modules and USB cable are sold separately. -
This module is made using Alcohol Gas Sensor MQ3. It is a low cost semiconductor sensor which can detect the presence of alcohol gases at concentrations from 0.05 mg/L to 10 mg/L. The sensitive material used for this sensor is SnO2, whose conductivity is lower in clean air. It’s conductivity increases as the concentration of alcohol gases increases. It has high sensitivity to alcohol and has a good resistance to disturbances due to smoke, vapor and gasoline. This module provides both digital and analog outputs. MQ3 alcohol sensor module can be easily interfaced with Microcontrollers, Arduino Boards, Raspberry Pi etc. -
Gas Sensor(MQ5) module is useful for gas leakage detection (in home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer. -
MQ 6 Gas sensor is used as LPG, Butane and Propane Sensor to generate alarm when there is leakage of these gases from the source. MQ6 is a highly sensitive gas sensor to petroleum based gases but less sensitive to Alcohol and Carbon di oxide. This simple sensor can be installed in the kitchen to give warning alarm if there is leakage of LPG. -
The MQ series of gas sensors use a small heater inside with an electro-chemical sensor. They are sensitive for a range of gasses and are used indoors at room temperature. The output is an analog signal and can be read with an analog input of the Arduino. The MQ-2 Gas Sensor module is useful for gas leakage detecting in home and industry. It can detect LPG, i-butane, propane, methane ,alcohol, hydrogen and smoke. -
A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of bend). Connector is 0.1" spaced and bread board friendly. Check datasheet for full specifications. -
A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. The resistance of the flex sensor changes when the metal pads are on the outside of the bend (text on inside of bend). Connector is 0.1" spaced and bread board friendly. Check datasheet for full specifications. -
This is a 12V 1-Channel Relay interface board which can be controlled directly by a wide range of micro controllers such as Arduino, AVR, PIC, ARM, 8051 and so on. It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High quality screw terminals (Terminal Block) provided (C, NC , NO) for quick and easy connection LED Status indicators to indicate the relay ON/OFF status. -
This is a 4 channel relay module. It can be used to control the lighting, electrical and other equipment. The modular design makes it easy to expand with the Arduino board or other MCU board PIC, ARM and MSP430. The Relay output state by a light-emitting diode. -
The 8 channel 12V relay module provides 8 optically isolated inputs that accept a wide range of voltage. This is a great way to switch on or off AC or DC loads using your Arduino. The relays are single-pole double-throw (SPDT) and are rated for 10A @ 250VAC. The ground for the relay coils is separate from the ground for the input signals. This, along with the optical isolation, provides a total galvanic isolation between the input and output. The two grounds could be joined together if desired with the included jumper. The relay coils run on 12VDC, and the module has screw-terminal blocks for sturdy and reusable attachments for the external load. The signal and power inputs run through the male single-row header. -
DTMF Refers to Dual Tone Multi-Frequency Signaling. This DTMF is used for telecommunication signaling over analog telephone lines in the voice-frequency band between telephone handsets and other communications devices and the switching center. -
This module allows you to detect when sound has exceeded a set point you select. Sound is detected via a microphone and fed into an LM393 op amp. The sound level set point is adjusted via an on board potentiometer. When the sound level exceeds the set point, an LED on the module is illuminated and the output is sent low. -
The TCS230 programmable color light-to-frequency converter combines configurable silicon photodiodes and a current-to-frequency converter on single monolithic CMOS integrated circuit. The output is a square wave (50% duty cycle) with frequency directly proportional to light intensity (irradiance). The full-scale output frequency can be scaled by one of three preset values via two control input pins. Digital inputs and digital output allow direct interface to a microcontroller or other logic circuitry. Output enable (OE) places the output in the high-impedance state for multiple-unit sharing of a microcontroller input line. -
L293D Motor Driver Board E-40 L293D Motor Driver shield Input Voltage Range: 4.5 To 24VDC Output current Per Channel: 600mA Peak Output current: 1.2A -
HC-06 RF Wireless Bluetooth Transceiver Slave Module RS232 / TTL to UART converter and adapter. This module is an Upgrade from the older HC-05 and has better stable Firmware. Features: Bluetooth Serial Transceiver Module with backboard. This module includes key interface and state interface compared with Smart Bluetooth Module Baseboard. The Bluetooth Module Baseboard can be compatible with slave mode. Works for Bluetooth TTL transceiver module which allows your target device to both senders receive the TTL data. The key interface on the baseboard is the master mode button and can be controlled by high level from external MCU, and then this module will search again automatically. Built in antenna Bluetooth version: V2.0 EDR -
This module integrates DHT11 sensor and other required components on a small PCB. The DHT11 sensor includes a resistive-type humidity measurement component, an NTC temperature measurement component and a high-performance 8-bit micro controller inside, and provides calibrated digital signal output. It has high reliability and excellent long-term stability, thanks to the exclusive digital signal acquisition technique and temperature & humidity sensing technology. -
Stable and reliable chipset CP2102 USB specification 2.0 compliant with full-speed 12Mbps. Standard USB type A male and TTL 5pin Supports windows vista/xp/server 2003/200,Mac OS-X/OS-9,Linux Temperature Range: -40Cto 85C -
This is the HC-SR04 ultrasonic ranging sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04 module includes an ultrasonic transmitter, a receiver and a control circuit. -
4 pins Power supply: 5V DC Static current: 2mA Sensor angle: 15 to 35 degrees Sensing distance: 0.75in (2cm) to 13ft (4m) Precision: up to 0.04in (1.0mm) -
Usage： Supply module with 6-12V, the output will be 5V while obstacle in range, or 0V if not. The out pin of this module is used as a switching output when anti-theft module, and without the feet when ranging modules, Note : the module should be inserted in the circuit before been power, which avoid producing high level of misoperation ；if not, then power again. -
The SRF05 is an evolutionary step from the SRF04, and has been designed to increase flexibility, increase range, and to reduce costs still further. As such, the SRF05 is fully compatible with the SRF04. Range is increased from 3 meters to 4 meters. A new operating mode (tying the mode pin to ground) allows the SRF05 to use a single pin for both trigger and echo, thereby saving valuable pins on your controller. When the mode pin is left unconnected, the SRF05 operates with separate trigger and echo pins, like the SRF04. The SRF05 includes a small delay before the echo pulse to give slower controllers such as the Basic Stamp and Picaxe time to execute their pulse in commands
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
