-
4 pins Power supply: 5V DC Static current: 2mA Sensor angle: 15 to 35 degrees Sensing distance: 0.75in (2cm) to 13ft (4m) Precision: up to 0.04in (1.0mm) -
This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to -16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited to measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (4 mg/LSB) enables measurement of inclination changes less than 1.0 degrees;. -
The MPU-6050 is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis MotionFusion algorithms, the MPU-6050 does away with the cross-axis alignment problems that can creep up on discrete parts. Our breakout board for the MPU-6050 makes this tiny QFN package easy to work into your project. Every pin you need to get up and running is broken out to 0.1" headers, including the auxiliary master I2C bus which allows the MPU-6050 to access external magnetometers and other sensors. -
Magnetic fields and current go hand-in-hand. When current flows through a wire, a magnetic field is created. This is the basic principle behind electromagnets. This is also the principle used to measure magnetic fields with a magnetometer. The direction of Earth's magnetic fields affects the flow of electrons in the sensor, and those changes in current can be measured and calculated to derive a compass heading or other useful information -
The HDPMO1 is a dual-axis magnetic sensor, it is a complete sensing system with on-chip signal processing and integrated I2C bus, allowing the device to be connected directly to a microprocessor eliminating the need for A/D converters or timing resources. It can measure magnetic field with a full range of ±2 gausses and a sensitivity of 512counts/gauss @3.0 V at 25°C. -
he smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at any voltage! That’s right - power the board at 5V and the unit will convert RS232 to 5V TTL. Power the board at 2.8V and the Shifter board will convert RS232 to 2.8V CMOS TTL. Includes two indicator LEDs for TX and RX. Runs from 300bps up to 115200bps. -
Description This is a great little RFID Reader Module from Innovations, simillar to the ID models (the difference being no silicone protection on the back). If you need an inexpensive way to get started with RFID, this is a great little module. Just power the module, and it will read any RFID card within range. 1. Reading distance : 100mm 2. Frequncy:125Khz 3. Card format : EM4100 or compatible chip It will output the cards ID in a serial string, which can easily be read by any microcontroller. The spacing on the pins is 2.54 mm, which means the module will directly fit on a breadboard.Note: This Module will not work the Atmega32u2 Developement Board. Technical Specifications 1. 5V supply 2. 125kHz read frequency 3. EM4001 64-bit RFID tag compatible 4. 9600bps TTL and RS232 output 5. Magnetic stripe emulation output 6. 100mm read range 7. Interface: Wiegand 26 , RS232 8. Output: RS232 and WG26 9. Range of power supply: 4.6V to 5.4V 10.Encoding: Manchester 64-bit,modulus 64 -
This module directly connects to any microcontroller UART or through a RS232 converter to PC.It gives UART/Wiegand26 output. This RFID Reader Module works with any 125 KHz RFID tags 1.Specifications 5VDC through USB (External 5V supply will boost range of the module) Current: <50mA Operating Frequency: 125Khz Read Distance: 10cm Size of RFID reader module: 32mm(length) * 32mm(width) * 8mm(height) 2. RS232 interface format: 10 ASCII DATA (card no.) 2 ASCII DATA (XOR result) E.g. Card number is 4500C5D1E9B8 read from reader then the card number on card will be as below. 45 - Preamble 00C5D1E9 value in Hex = 12964329. / B8 is XOR value for (45 XOR 00 XOR C5 XOR D1 XOR E9) Hence number on the card is 0012964329. 1. Data baud rate: 9600 bps 2. Data bit 8 bits 3. Parity check: None 4. Stop bit -
RFID Reader Modem TTL
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
