-
The AM2302 is a wired version of the DHT22, in a large plastic body. It is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). -
1. Feature & Application: * Full range temperature compensated * Relative humidity and temperature measurement * Calibrated digital signal *Outstanding long-term stability *Extra components not needed * Long transmission distance * Low power consumption *4 pins packaged and fully interchangeable 2. Description: DHT22 output calibrated digital signal. It utilizes exclusive digital-signal-collecting-technique and humidity sensing technology, assuring its reliability and stability.Its sensing elements is connected with 8-bit single-chip computer. Every sensor of this model is temperature compensated and calibrated in accurate calibration chamber and the calibration-coefficient is saved in type of program in OTP memory, when the sensor is detecting, it will cite coefficient from memory. Small size & low consumption & long transmission distance(20m) enable DHT22 to be suited in all kinds of harsh application occasions. -
Features:- Fine and elegant workmanship
- Fast response time
- Strong anti-interfere
- Great performance
- Easy to install
- Material: Plastic
- Size: Approx. 61 x 27 x 16mm
- Inner size: Approx. 42.2 x 22.2mm
- Circuit board: Approx. 42 x 22mm
- Diagonal distance between two screws is 35.5mm
- If the thickness of board is 1.6mm, it can be equipped w/ 2.6 x 6mm screws
- If board is smaller than 1.6mm, it can be equipped w/ 5.5mm or shorter screws
- Suitable for sensor, SCM experiment
-
This module is based on the TDA7266 dual bridge audio amplifier chip, which features an output power of up to 7 W for each channel. It is suitable for use with 5 W to 15 W speakers. Specifications- On-board TDA7266 stereo audio amplifier chip
- Output: dual-channel 7W 7W
- On-board 5.08 mm terminal blocks for the left and right audio channels
- On-board potentiometer for volume adjustment
- DC power jack
- Operating Voltage Range: 3 V to 18 V
- Board Size: 45 x 33 mm
-
This custom designed module uses the DS1307 Real Time Clock to keep track of the current year, month, day as well as the current time. The module comes fully assembled and pre-programmed with the current time (OK, so it's MST current time). The DS1307 is accessed via the I2C protocol. -
Module description:
1 On board ATMega8A-AU chip 2 With power supply and two lights burning 3 Onboard 500mA PPTC overcurrent protection 4 On the target board support 5V and 3.3V powered byNo need to install drivers
The model from the latest applicable automatic speed control.
Suitable for WIN8.1 / 8/7 / XP32 bit / 64-bit computer systems.
-
Product Description:
Keep it cool with a Peltier module Thermoelectric Cooler . These unique electronic components can generate a temperature differential when powered. That is to say, apply 12V to the red (positive) and black (negative) wires and one side will get cold while the other side gets hot. For best results, you'll need to wick away that heat (otherwise the cold side will slowly get warmer). A fan and/or heatsink is ideal. This module is a 12V module, and is rated for ~72W max (up to 14V/6A) but when used with a regulated 12V output they don't draw more than 5A so we suggest our 12V/5A power adapter for use. -
Description: Here we have a Joystick shield that sits atop your Arduino and turns it into a simple controller. 7 momentary push buttons (4 big buttons, 2 small buttons, and a joystick select button) and a two-axis thumb joystick gives your Arduino functionality on the level of the old Nintendo controllers. -
The PCF8591 is a single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface. Three address pins A0, A1 and A2 are used for programming the hardware address, allowing the use of up to eight devices connected to the I2C-bus without additional hardware. Address, control and data to and from the device are transferred serially via the two-line bidirectional I2C-bus. -
WTV020-SD-16P is a low cost and easy to use MicroSD MP3 module which supports WAV and AD4 formats. It support upto 1GB SD cards. It requires a 3.3V power supply for its operation and its power consumption is very low. You can easily copy voice files to SD Card using PC and it should be in FAT format. This module can be easily interfaced with Arduino Boards, Microcontrollers etc. It can also be used as standalone without any MCU. Please read the datasheet carefully before using this module. -
Just like a joystick on game console. you can control x, y and z dimensions input by this joystick module. It can be considered as combination of potentiometers and one button. Data type of the x, y dimensions are analog input signals and z dimension is digital input signal. thus the x and y ports connect to analog pins of Sensor Shield, while z port connects to digital pin. When using, it can connect with Arduino sensor shield,and connect Arduino corresponding pins through Arduino sensor cables. -
Bee Adapter is a compact USB to serial adapter equipped with BEE (20pin 2.0mm) sockets. With integrated FT232RL IC, It can be used for programming or communicating with board which basic Arduino but without USB interface,like Sniffer Nano. On the other hand, you may connect your PC to various wireless applications via the BEE compatible modules. The adapter also support XBee module interface. -
This Arduino shield from Adafruit features TI’s CC3000 Wi-Fi module with an onboard ceramic antenna, a microSD card socket, and a designated prototyping area. The CC3000 uses SPI for communication instead of UART, so the communication speed is not limited to a fixed baud rate. It supports 802.11b/g, open/WEP/WPA/WPA2 security, TKIP, and AES, and a built-in TCP/IP stack with a BSD socket interface supports TCP and UDP in client and server mode with up to 4 concurrent socket connections. -
Description: The GPRS Shield is based on SIM900 module from SIMCOM and compatible with Arduino and its clones. The GPRS Shield provides you a way to communicate using the GSM cell phone network. The shield allows you to achieve SMS, MMS, GPRS and Audio via UART by sending AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands). The shield also has the 12 GPIOs, 2 PWMs and an ADC of the SIM900 module(They are all 2V8 logic) present onboard.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
