-
This is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE it is a great way to jump into electronics, or perfect for when an Arduino is too big or too much. Features : -Support for the Arduino IDE 1.0 (OSX/Win/Linux). -Power via USB or External Source - 5v or 7-35v (12v or less recommended, automatic selection). -On-board 500ma 5V Regulator. -Built-in USB. -6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB). -8k Flash Memory (about 6k after bootloader). -I2C and SPI (vis USI). -PWM on 3 pins (more possible with Software PWM). -ADC on 4 pins. -Power LED and Test/Status LED.
-
Description:
GH100 Miniature Microwave Motion Sensor is a X-Band Bi-Static Doppler transceiver module. Its built-in Dielectric Resonator Oscillator (DRO) and a pair of Microstrip patch antenna array, make it ideal for OEM usage in motion detection equipment. This module is ideally suitable for false alarms reduction in intruder detectors when work together with Passive Infrared (PIR) sensor. It can also be used for auto-door opening and vehicle speed measurement.Features:
- Low current consumption
- CW or Pulse operation
- Flat profile
- Microwave-PIR motion detector
- Speed measurement
- Lighting control
- Long detection range
- Antenna Beam Pattern
- Azimuth
-
OP8 to DIP8 8 pin chip programmer adapter is wide body, 1.27 mm Pitch and 7.9 mm Width, this SOP8 / SOIC8 / SO8 8 pin ic socket support eeprom from width 200mil to 208mil, SOP8 to DIP8 8 pin IC socket will convert SOP8 into DIP8. Features: 1. CNV SOP8、SOIC8、SO8 8 pin ic socket 2. Tested before shipping 3. Easy to use, support eeprom width 200mil-208mil 4. Wide body SOP8 8 pin ic socket Supported Devices (Wide): 1. Package: SOP8、SOIC8、SO8 2. Pitch: 1.27 mm 3. Width: 7.9 mm (add pin width) 4. Width: 5.4 mm 5. SOP 8 Pin to DIP 8 Pin, Pitch: 2.54mm (100mil), Width: 1.52cm (600mil)
-
SSOP16 16 pin ic socket work with any IC chip in an 16-pin SSOP package, ssop16 16 pin ic socket will enable convert SSOP 16 Pin to DIP 16 Pin, the SSOP 16 pin to DIP 16 pin adapter that you can plug into an 16-pin DIP socket.
CNV ssop16 16 pin ic socket 0.65mm tssop16 16 pin ic socket Features: 1. CNV SSOP 16 pin ic socket 2. Tested before shipping 3. Easy to use -
Specifications: -5V solid state relays 240V 2A, output with resistive fuse 240V 2A. -2.54cm pin and blue KF301 terminals to the control line is more convenient. -The input power supply: 5V DC (160MA) -The input control signal voltage: 0-2.5V low state relay OFF; -3.3-5V high state relay ON -Size: 57 x 55 x 20 mm(L x W x H)
-
Multi function shield Features -4 digit 7-segment LED display module driven by two serial 74HC595’s. -4 LED’s. -10K potentiometer. -3 x push buttons. -Piezo buzzer. -DS18B20 temperature sensor interface (not included). -Infrared receiver interface. -Serial interface header for connection to serial modules.
-
Features:
- Light weight, small size, easy to install.
- Inlaid with stainless steel impeller shaft, durable wearable.
- Seal ring with the upper and lower force structure never leaks.
- Non-violent shock, and chemical erosion.
- Non-throwing or hitting.
- Mounted vertically, should not exceed 5 degrees inclination.
- Temperature of medium should not exceed 120 ℃.
-
PM2.5 GP2Y1010AU0F Dust Smoke Particle Sensor E-242 Power supply voltage: DC5 ± 2V Sensitivity: 0.5V / (0.1mg / m3) The minimum detection level of particles: 0.8 m Clean air voltage: 0.9V typ. Low consumption current (Icc: MAX. 20 mA) The presence of dust can be detected by the photometry of only one pulse Enable to distinguish smoke from house dust
-
- Supports Multiple Baud rates (4800/9600/19200/38400).
- Works on ISM band (2.4 GHz) which is reserved internationally so no need to apply for license.
- No complex wireless connection software or intimate knowledge of RF is required to connect your serial devices.
- Designed to be as easy to use as cables.
- No external Antenna required.
- Plug and play device.
- Works on 5-9v DC supply.
- Standard UART Interface.