-
MF RC522 is a highly integrated read and write card chip applied to the 13.56MHz contactless communication.It is a low-voltage, low-cost, and small-sized non-contact card chip, a best choice for intelligent instrument and portable handheld devices. The MF RC522 uses advanced modulation and demodulation concept which fully presented in all types of 13.56MHz passive contactless communication methods and protocols. In addition, it supports rapid CRYPTO1 encryption algorithm to verify MIFARE products. MFRC522 also supports MIFARE series of high-speed non-contact communication, with a two-way data transmission rate of up to 424kbit/s. As a new member of the 13.56MHz highly integrated reader card series, MF RC522 is much similar to the existing MF RC500 and MF RC530 when there are also great differences. It communicates with the host machine via the serial manner which needs less wiring. You can choose between SPI, I2C and serial UART mode (similar to RS232), which helps reduce the connection, save PCB board space (smaller size), and reduce cost.
-
This module directly connects to any microcontroller UART or through a RS232 converter to PC.It gives UART/Wiegand26 output. This RFID Reader Module works with any 125 KHz RFID tags 1.Specifications 5VDC through USB (External 5V supply will boost range of the module) Current: <50mA Operating Frequency: 125Khz Read Distance: 10cm Size of RFID reader module: 32mm(length) * 32mm(width) * 8mm(height) 2. RS232 interface format: 10 ASCII DATA (card no.) 2 ASCII DATA (XOR result) E.g. Card number is 4500C5D1E9B8 read from reader then the card number on card will be as below. 45 - Preamble 00C5D1E9 value in Hex = 12964329. / B8 is XOR value for (45 XOR 00 XOR C5 XOR D1 XOR E9) Hence number on the card is 0012964329. 1. Data baud rate: 9600 bps 2. Data bit 8 bits 3. Parity check: None 4. Stop bit
-
RGB LED module consists of a plug-in full color LED made by R, G, B three pin PWM voltage input can be adjusted Section three primary colors (red / blue / green) strength in order to achieve full color mixing effect. Control of the module with the Arduino can be achieved Cool lighting effects.
Specifications
- the use of plug-in full-color LED
- RGB trichromatic limiting resistor to prevent burnout
- through the PWM adjusting three primary colors can be mixed to obtain different colors
- with a variety of single-chip interface
- the working voltage: 5V
- LED drive mode: common cathode driver
-
he smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at any voltage! That’s right - power the board at 5V and the unit will convert RS232 to 5V TTL. Power the board at 2.8V and the Shifter board will convert RS232 to 2.8V CMOS TTL. Includes two indicator LEDs for TX and RX. Runs from 300bps up to 115200bps.
-
Duty Cycle : 10%;Rated Voltage : AC 220V;Action Form : PushStroke : 10mm;Force : 300gf;Current : 1ATotal Size : 5.5 x 4 x 2.7cm/2.2'' x 1.6'' x 1.1'' (L*W*H);Coil Size : 2.9 x 2.6cm/1.1'' x1''(L*D);Plunger Diameter : 0.6cm/0.2''Cable Length : 19cm/7.5'';Net Weight : 99g;Package Content : 1 x Open Frame Solenoid Electromagnet Push type, open frame style, open coil form, AC electromagnet. Used widely in banking ATM, vending machines, electronic appliances, embroidery machines, intelligent lock, juice bread maker, textile machines, cash register or other automatic control devices.
-
The GP2Y0A710K infrared sensor is a new version of GP2Y0A700K which takes a continuous distance reading and reports the distance as an analog voltage with a distance range of 1m (39.3") to 5.5m (216.5"). The interface is 5-wire JST connector (included with pins) with dual Vcc, dual Gnd, and a single output voltage. Power, ground and signal wiring is enough to read a continuous analog voltage representing distance. A software lookup table can be implemented to translate the voltages to distances.