-
Product Features: 1. Toshiba TB6560AHQ chip - maximum 3.5 Adrive current, more powerful. 2. 1 - 1/16 microstep setting - higher accuracy, smoother operation. 3. Overload & over-current & over-temperature protection, full protection of your computer and peripheral equipment. 4. 4 files current settings can be set according to the user the actual current requirement. 5. Full closed-type optical isolation to protect the user's computer and equipment. 6. Professional design, two-stage signal processing, super anti-jamming. 7. Bipolar constant current chopper drive motor low-speed non-creeping phenomenon, noise, non-resonant region. 8. Four input control, you can set limit, emergency stop, which is divided into pairs of knives.
-
Microchip has gone on to manufacture the PICkit 3, a variation of the PICkit 2 with the same form factor and a new translucent case. It features a faster 16-bit PIC24F processor and a wider voltage regulation range. There are some complaints of it not being as reliable as the Pickit 2. Both PICkit 2 and PICkit 3 have internal, switch-mode voltage regulators. This allows them, in the case of the PICkit 2, to generate voltages from 2.5 to 5 volts, or in the case of the PICkit 3, 2.5 to 5.5 volts, from a 5 V USB supply, at around 100 mA. Both have options for calibrating the output with a multimeter, for increased accuracy. Additionally, for some PICs, the MCLR programming voltage can be generated, at around 13 to 14 volts. This voltage is required to reprogram the flash memory.
-
Overview:
- Small kit, easy to use .
- The LCD driver board is HDMI/VGA/2AV Reversing Driver board.
- This controller board supports Automatically Switch to AV2(Reversing View camera). Please connected ACC to 12V. Power Supply is NOT included.
- If you want to conect this screen to your Raspberry Pi, you need a AV Cable or a HDMI Cable, or if you have a HDMI TO VGA CABLE for Raspberry pi, you can use a VGA Cable to connect your Raspberry pi to this Screen.
- There is a sticker on the LCD screen. Please peel off before use.
-
BeagleBone Black is a low-cost, community-supported development platform for developers and hobbyists. Boot Linux in under 10 seconds and get started on development in less than 5 minutes with just a single USB cable. Processor: AM335x 1GHz ARM® Cortex-A8 512MB DDR3 RAM 4GB 8-bit eMMC on-board flash storage 3D graphics accelerator NEON floating-point accelerator 2x PRU 32-bit microcontrollers
-
1. STM32F103RCT6: the high performance STM32 MCU in LQFP64 package which features * Core: ARM Cortex-M3 32-bit RISC; * Operating Frequency: 72MHz, 1.25 DMIPS/MHz; * I/Os: 51; * Operating Voltage: 2-3.6V; * Memories: 256kB Flash, 48kB RAM; * Communication Interfaces: 2 x SPI, 5 x USART, 2 x I2S, 2 x I2C, 1 x SDIO, 1 x USB, 1 x CAN; * AD & DA converters: 3 x AD(12-bit, 1s, shares 16 channels); 2 x DA(12-bit); * Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP; 2. AMS1117-3.3V: 3.3V voltage regulator; 3. Power supply switch: 5V DC or USB; 4. Power indicator; 5. LEDs: Convenient for indicating I/O status or program debugging running state; 6. Reset button; 7. User key; 8. Joystick: Convenient for I/O input (five positions); 9. 32.768K crystal oscillator: used for internal RTC, also supports clock calibration; 10. 8M crystal oscillator: enables the MCU run at 72M frequency by frequency multiplication; 11. SDIO Interface: connects to the Micro SD adapter easily, It is much faster to read/write the Micro SD card via SDIO than via SPI; 12. 8-Bit I/O Interface: easily connects to keypad, motor, etc; 13. CAN Interface: communicates with accessory boards which feature the CAN device conveniently; 14. SPI1 / SPI2 interface: * Easily connects to SPI peripherals such as FLASH (AT45DBxx), SD card, MP3, etc.; * Convenient for connecting AD, DA module, thanks to the SPI1 alternative function - AD&DA; 15. I2C1 / I2C2 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.; 16. LCD Interface: easily connects to the touch screen LCD; 17. ONE-WIRE Interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc. 18. PS/2 Interface: easily connects to PS/2 keyboard or mouse; 19. USART1 Interface: easily connects to RS232, RS485, USB TO 232; 20. USART2 Interface: easily connects to RS232, RS485, USB TO 232; 21. USB Port: USB communication between board and PC; 22. 5V DC jack; 23. 5V/3.3 V power input/output: usually used for power output, or common ground with other user board; 24. MCU pins connector: all the MCU pins are accessible on expansion connectors for further expansion; 25. JTAG/SWD interface: for debugging/programming; 26. Boot Mode Selection: for configuring the BOOT0 and BOOT1 pins.
-
Description TOP2011 USB Universal Programmer 100% is original one,Top2011 Eprom Programmer Supports Windows 98se/ME/2000/XP/Vista/Win7,TOP 2011 Universal Programmer is the best chip universal programmer TOP2011 USB Universal Programmer Features USB powered, 70mA~500mA, No AC/DC adapter needed. Support 2.5V~6.5V device. Over-current protection on all Pins. 40 pins self-lock sockets. Working with Windows XP/Vista/Win7(32-bit). Self-detecting the device’s manufacturer’s name and the type of IC. Topwin 2011 EEPROM programmer speciality 100% Brand New Model : TOP2011 40 pins self-lock sockets USB load testing (0 to 10 levels) Interface with PC , laptop or compatibles through USB1.1/2.0 port Self-detecting the device’s manufacturer’s name and the type of IC Provides over-current and over-voltage protection for safety of the chip and programmer hardware Support devices 2.5V~6.5V Power : < 2.5w (5v/500mA) Supports Windows 98/SE/ME/2000/XP/Vista/Win7
-
Raspberry Pi 5 Model 8GB E-890 2.4GHz quad-core, 64-bit Arm Cortex-A76 CPU, with 512KB L2 caches and a 2MB shared L3 cache Video Core VII GPU LPDDR4X-4267 8GB SDRAM 2.4 GHz and 5.0 GHz 802.11ac Wi-Fi. Bluetooth 5.0 / Bluetooth Low Energy (BLE) Micro SD card slot, with support for high-speed SDR104 mode 2 USB 3.0 ports, supporting simultaneous 5Gbps operation 2 USB 2.0 ports Gigabit Ethernet, with PoE+ support (requires PoE+ HAT) 2 4 lane MIPI camera/display transceivers PCIe 2.0 x1 interface for fast peripherals 5V/5A DC power (PD enabled) Raspberry Pi standard 40-pin header Real-Time Clock (RTC), powered by an external battery On-board power button!!