-
he smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at any voltage! That’s right - power the board at 5V and the unit will convert RS232 to 5V TTL. Power the board at 2.8V and the Shifter board will convert RS232 to 2.8V CMOS TTL. Includes two indicator LEDs for TX and RX. Runs from 300bps up to 115200bps. -
SCT-013-030 Non-invasive AC Current Sensor Clamp Sensor 30A E-619 Input Current : 0-30A Output Mode: 0-1V @ 30mA Dielectric Strength 6000V AC/1min -
The SD Card Shield is a simple solution for transferring data to and from a standard SD card. The pinout is directly compatible with Arduino, but can also be used with other microcontrollers. It allows you to add mass storage and data logging to your project. -
Duty Cycle : 10%;Rated Voltage : AC 220V;Action Form : PushStroke : 10mm;Force : 300gf;Current : 1ATotal Size : 5.5 x 4 x 2.7cm/2.2'' x 1.6'' x 1.1'' (L*W*H);Coil Size : 2.9 x 2.6cm/1.1'' x1''(L*D);Plunger Diameter : 0.6cm/0.2''Cable Length : 19cm/7.5'';Net Weight : 99g;Package Content : 1 x Open Frame Solenoid Electromagnet Push type, open frame style, open coil form, AC electromagnet. Used widely in banking ATM, vending machines, electronic appliances, embroidery machines, intelligent lock, juice bread maker, textile machines, cash register or other automatic control devices. -
The detection range of this version is approximately 20 cm to 150 cm (8″ to 60″). The GP2Y0A02 uses a 3-pin JST PH connector that works with our 3-pin JST PH cables for Sharp distance sensors ; the top picture on the right shows a shorter-range Sharp analog distance sensor with one of these cables. -
The GP2Y0A710K infrared sensor is a new version of GP2Y0A700K which takes a continuous distance reading and reports the distance as an analog voltage with a distance range of 1m (39.3") to 5.5m (216.5"). The interface is 5-wire JST connector (included with pins) with dual Vcc, dual Gnd, and a single output voltage. Power, ground and signal wiring is enough to read a continuous analog voltage representing distance. A software lookup table can be implemented to translate the voltages to distances. -
This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. These sensors are good for short-range detection. • Infrared range finder 10cm (~4") to 80cm (~30") • Analog interface • Lead free, ROHS compliant • Replaces the discontinued GP2D12 -
Features:- Fine and elegant workmanship
- Fast response time
- Strong anti-interfere
- Great performance
- Easy to install
- Material: Plastic
- Size: Approx. 61 x 27 x 16mm
- Inner size: Approx. 42.2 x 22.2mm
- Circuit board: Approx. 42 x 22mm
- Diagonal distance between two screws is 35.5mm
- If the thickness of board is 1.6mm, it can be equipped w/ 2.6 x 6mm screws
- If board is smaller than 1.6mm, it can be equipped w/ 5.5mm or shorter screws
- Suitable for sensor, SCM experiment
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
