-
Features
- Supports following Hardwired TCP/IP Protocols : TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
- Supports 8 independent sockets simultaneously
- Supports Power down mode
- Supports Wake on LAN over UDP
- Supports High Speed Serial Peripheral Interface(SPI MODE 0, 3)
- Internal 32Kbytes Memory for Tx/Rx Buffers
- 10BaseT/100BaseTX Ethernet PHY embedded
- Support Auto Negotiation (Full and half duplex, 10 and 100-based)
- Not support IP Fragmentation
- 3.3V operation with 5V I/O signal tolerance
- LED outputs (Full/Half duplex, Link, Speed, Active)
Specifications
- Module size: 55mm x 28mm
- Power supply: 3.3v /5v
- SPI clock frequency(MAX): 80M
- Work current(typ): 128mA
-
Here is a motor speed sensor module, the major goal is to check the rate of an electric motor. The module can be used in association with a microcontroller for motor speed detection, pulse count, position limit, etc. In principle, any rate meter simply measures the rate at which some event occurs. Usually this is done by counting the events for a given period of time (integration interval) and then simply dividing the number of events by the time to get the rate.
-
DescriptionThis is a speed sensor, the major goal is to check the rate of motor.It was widely used in motor speed detection, pulse count, the position limit, etc.Features:-Groove type optical coupling sensor-The output state light, lamp output level, the output low level light.-Covered, output high level;Without sunscreen, the output low level.-The comparator output signal is clean, good waveform, driving ability is strong, for more than 15 ma.-It has a fixed bolt hole, convenient installation.
-
1, AO, analog output, real-time output voltage signal of the microphone 2, DO, when the sound intensity reaches a certain threshold, the output signal [high and low threshold - Sensitivity adjustment by potentiometer] Module features: 1, there is mounting screw holes of 3mm. 2, using the 5v DC power supply. 3, the analog output. 4, there is a threshold level output flip. 5, High sensitivity microphone, high sensitivity. 6, a power indicator light. 7, the comparator output indicator lamp.
-
OP8 to DIP8 8 pin chip programmer adapter is wide body, 1.27 mm Pitch and 7.9 mm Width, this SOP8 / SOIC8 / SO8 8 pin ic socket support eeprom from width 200mil to 208mil, SOP8 to DIP8 8 pin IC socket will convert SOP8 into DIP8. Features: 1. CNV SOP8、SOIC8、SO8 8 pin ic socket 2. Tested before shipping 3. Easy to use, support eeprom width 200mil-208mil 4. Wide body SOP8 8 pin ic socket Supported Devices (Wide): 1. Package: SOP8、SOIC8、SO8 2. Pitch: 1.27 mm 3. Width: 7.9 mm (add pin width) 4. Width: 5.4 mm 5. SOP 8 Pin to DIP 8 Pin, Pitch: 2.54mm (100mil), Width: 1.52cm (600mil)
-
SOP28 to DIP28 28 pin IC socket will convert SOP28 into DIP28, SOP28 / SOIC28 / SO28 IC Programmer Adapter is 1.27 mm Pitch and 7.5 mm Width, SOP28 8 pin programmer adapter. SOP28 to DIP28 28 pin IC socket SOIC28 IC adapter. Features: 1. CNV SOP28、SOIC28、SO28 28 pin ic socket 2. Tested before shipping 3. Easy to use
-
SSOP16 16 pin ic socket work with any IC chip in an 16-pin SSOP package, ssop16 16 pin ic socket will enable convert SSOP 16 Pin to DIP 16 Pin, the SSOP 16 pin to DIP 16 pin adapter that you can plug into an 16-pin DIP socket.
CNV ssop16 16 pin ic socket 0.65mm tssop16 16 pin ic socket Features: 1. CNV SSOP 16 pin ic socket 2. Tested before shipping 3. Easy to use -
- Product Name : DC Solenoid Electromagnet;Model : 0520S-24B70;Rated Voltage : DC 24V
- Current : 0.34A;Power : 8.22W;Type : Pull
- Start Force & Stroke : 5mm 0.003Kg;End Force & Stroke : 0mm 0.1Kg;Total Size : 3.5 x 1.5 x 1.2cm/1.4" x 0.59" x 0.47"(L*W*T)
- Shaft Diameter : 5mm/0.2";Cable Length : 13cm /5.1";Material : Metal, Electronic Parts
- Weight : 20g;Package Content : 1 x DC Solenoid Electromagnet
-
Rated Voltage DC 6.0V DC 9.0V DC 12.0V Max Current <350MA <250mA <180mA Rated Power 2~3.5W Water Pressure 0~70KPA Water Flow 0.5~0.8LPM Leakage <9mmHg/min(inflating from 0 to 300 -10mmHg in a 100cc tank and then stoping for 30sec.) Apply Air,Water Life Test Power on 30sec.and then Power off 20sec. About 30,000 times. Temperature 0~55℃