-
200grm Straight Bar Mini Load Cell RSN-157 Weight Capacity Max - 200 g Maximum Overload - 220 g Cell Repeatability Error Max - ± 50 mg Cell Non-Linearity Max - 50 mg Cell Hysteresis Max - 50 mg Electrical Properties Rated Output - 600 μV/V Rated Output Error Max ± 150 μV/V Output Impedance 1 kΩ Creep 100 mg/hr Temperature Effect on Zero 5 mg/°C Temperature Effect on Span 5 mg/°C Supply Voltage Min 3 V DC Supply Voltage Max 10 V DC Zero Balance Ratio ± 100 μV/V Material - Aluminium Alloy (LY12CZ) Screw Thread Size - 2.5M 47mm x 12mm x 6mm, 110mm Wire -
This is the HC-SR04 ultrasonic ranging sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04 module includes an ultrasonic transmitter, a receiver and a control circuit. -
This module integrates DHT11 sensor and other required components on a small PCB. The DHT11 sensor includes a resistive-type humidity measurement component, an NTC temperature measurement component and a high-performance 8-bit micro controller inside, and provides calibrated digital signal output. It has high reliability and excellent long-term stability, thanks to the exclusive digital signal acquisition technique and temperature & humidity sensing technology. -
This module allows you to detect when sound has exceeded a set point you select. Sound is detected via a microphone and fed into an LM393 op amp. The sound level set point is adjusted via an on board potentiometer. When the sound level exceeds the set point, an LED on the module is illuminated and the output is sent low. -
Highlights: By adjusting the potentiometer can set the length of time. MicroUSB 5.0V power supply with an input port, easy to use. 5 ~ 30V wide supply voltage. External signaltrigger and keytriggerin two ways. With a relay indicator. Anti-interference ability, the relay at various interference will not misoperation, suitable for industrial control. -
The module (MicroSD Card Adapter) is a Micro SD card reader module, through the file system and the SPI interface driver, MCU to complete the file system to read and write MicroSD card. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write. -
Specifications Modulation: Digital Torque: 4.8V: 130.54 oz-in (9.40 kg-cm) 6.0V: 152.76 oz-in (11.00 kg-cm) Speed: 4.8V: 0.20 sec/60° 6.0V: 0.16 sec/60° Weight: 1.94 oz (55.0 g) Dimensions: Length:1.60 in (40.7 mm) Width:0.78 in (19.7 mm) Height:1.69 in (42.9 mm) Gear Type: Metal Pulse Cycle: 1 ms Connector Type: JR -
Supply voltage: 5V the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself).# Image shown is a representation only #
-
MQ-135 is sensitive air quality sensor that detects NH3, NOx, alcohol, benzene, smoke, CO2, etc. Heater voltage 5V, 31 ohm (40mA consumption) The board has digital and analog output.FEATURES
- Detects NH3, NOx, alcohol, benzene, smoke, CO2, etc.
- Operating voltage 5V
- Operating current 40mA
- Both digital and analog output
- Popular sensor - a lot of examples available for different platforms
- Port explanation : AO for analog output, DO for digital output, GND for ground, VCC for 5V voltage input
-
ESP-12E WiFi module is developed by Ai-thinker Team. core processor ESP8266 in smaller sizes of the module encapsulates Tensilica L106 integrates industry-leading ultra low power 32-bit MCU micro, with the 16-bit short mode, Clock speed support 80 MHz, 160 MHz, supports the RTOS, integrated Wi-Fi MAC/BB/RF/PA/LNA, on-board antenna. The module supports standard IEEE802.11 b/g/n agreement, complete TCP/IP protocol stack. Users can use the add modules to an existing device networking, or building a separate network controller. ESP8266 is high integration wireless SOCs, designed for space and power constrained mobile platform designers. It provides unsurpassed ability to embed Wi-Fi capabilities within other systems, or to function as a standalone application, with the lowest cost, and minimal space requirement. -
A versatile relay board with opto-isolated input. The relay channel can drive up to 10A @28VDC- 5V supply voltage / input signals
- Jumper to select high/low
- Equiped with a high-current relay (10A @ 28VDC)
- 2x LEDs that show the current state of the relay
-
Bring oscillation source Audino 9012 drive Work Voltage:3.3V-5V Set bolt hole, easy to assemble PCB Dimension:3.3cm*1.3cm It and your Arduino will be able to play melodies. This is a small buzzer for the Sensor Shield. It creates different sound based on the different frequency of I/O toggling. Pin Definition : Vcc : 3.3V-5V GND : The Ground I/O : I/O Interface of SCM -
1, AO, analog output, real-time output voltage signal of the microphone 2, DO, when the sound intensity reaches a certain threshold, the output signal [high and low threshold - Sensitivity adjustment by potentiometer] Module features: 1, there is mounting screw holes of 3mm. 2, using the 5v DC power supply. 3, the analog output. 4, there is a threshold level output flip. 5, High sensitivity microphone, high sensitivity. 6, a power indicator light. 7, the comparator output indicator lamp. -
Resistive touch screen TFT LCD, 3.5inch, 480x320 resolution 4-wire resistive touchscreen 8-bit digital interface, plus 4 control lines
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
