-
Voltage to Current Module 0-5V to 4-20mA Current Transmitter E-863 Supply Voltage range : 7-30vdc Wide input range : 0-2.5V. Industry-standard 4-20mA current output. -
VS1003 is an MP3 module with on-board microphone, it supports audio decoding formats of MP3, MP3 V, WMA, WAV, MIDI and the SP-MIDI.Features
- Separate analog, digital and IO power supply; serial data and control interface (SPI).
- 1 headphones and audio output interface, the internal PLL clock frequency multiplier; high-quality stereo DAC, 16-bit adjustable-chip ADC, high-quality stereo earplugs drive (30 EURO)
- A microphone for recording, support for recording encoding format: IMA ADPCM (monaural).
- 1 ine_in input interface supports two input methods; supports MP3 and WAV streams.
- Separate analog, digital and IO power supply
- On-board 3.3V and 2.5V LDO chip AMS-1117, the largest current provide of 800mA.
- Single power supply: 5 VDC, capacitor filter.
- 12.288 MHz crystal.
-
W5500 Ethernet shield is designed using the WIZnet W5500 chip. It supports both 3.3V & 5V. This Ethernet Shield is compatible with Arduino and ARM embed Platform. Features -Suppport 3.3V / 5V. -High Speed Ethernet controller W5500 chip. -SPI interface. -Internal 32Kbytes Tx/Rx buffer. -10/100 Ethernet PHY embedded. -Support Auto Negotiation (Full / Half duplex, 10 / 100-based). -Hardwired TCP/IP Protocols : TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE. -User Selectable GPIO pin. -Support SD-card slot for storage. -Support I2C, UART interface. -
W5500 TCP / IP SPI to LAN Ethernet Interface SPI to LAN / Ethernet Converter E-1014 80MHz high-speed SPI interface Built-in hardware TCPIP protocol stack, users need almost no knowledge of complex network protocols Support up to 8 Socket connections Support TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE protocol Integrated data link layer, physical layer Support power-down wake up Support high-speed serial peripheral interface (SPI mode 0~3) Internal 32K byte send and receive buffer Embedded 10BaseT/100BaseTX Ethernet Physical Layer (PHY) Support auto-negotiation (10/100-Based full/half-duplex) IP fragmentation is not supported 3.3V working voltage, I/O signal port 5V withstand voltage LED status display (full-duplex / half-duplex, network connection, network speed, active status) Ultra-small pin package for easily embedded applications Provide C application routines -
Water sensor brick is designed for water detection, which can be widely used in sensing rainfall, water level, and even liquid leakage. Water Detector / Sensor Connecting a water sensor to an Arduino is a great way to detect a leak, spill, flood, rain, etc. It can be used to detect the presence, the level, the volume and/or the absence of water. While this could be used to remind you to water your plants, there is a better Grove sensor for that. The sensor has an array of exposed traces, which read LOW when water is detected. -
Waterproof Ultrasonic Distance Sensor A0221AU (3~450cm, UART, IP67) E-1027 Operating Voltage: 3.3~5V Average Current: <8mA Blind Zone Distance: 3cm Detecting Range(Flat object): 3-450cm Output: URAT Response Time:100ms Operating Temperature: -15~60℃ Storage Temperature: -25~80℃ Reference Angle: 60º Waterproof Grade: IP67 -
# Image shown is a representation only #
Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz -
The Winson WCS1600 current sensor provides economical and precise solution for both DC and AC current sensing in industrial, commercial and communications systems. The unique package provides easy implementation without breaking original system and makes current sensing possible. Typical applications include motor control, load detection and management, over-current fault detection and any intelligent power management system etc. -
WG0101- 2.4 INCH 6-DIGIT 7-SEGMENT LCD DISPLAY MODULE FOR BACKLIGHT COLOR: GREEN E-756-A Working voltage: 4.7 – 5.0V DC Driver IC: HT1621 compatibility: can be directly connected to Arduino board, 51, AVR board -
WG0101- 2.4 INCH 6-DIGIT 7-SEGMENT LCD DISPLAY MODULE FOR BACKLIGHT COLOR: WHITE E-756 Working voltage: 4.7 - 5.0V DC Driver IC: HT1621 compatibility: can be directly connected to Arduino board, 51, AVR board
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
