-
A wireless radio frequency (RF) transmitter and receiver can be easily made using HT12D Decoder, HT12E Encoder and ASK RF Module. Wireless transmission can be done by using 433Mhz or 315MHz ASK RF Transmitter and Receiver modules. In these modules digital data is represented by different amplitudes of the carrier wave, hence this modulation is known as Amplitude Shift Keying (ASK). Radio Frequency (RF) transmission is more strong and reliable than Infrared (IR) transmission due to following reasons : Radio Frequency signals can travel longer distances than Infrared. Only line of sight communication is possible through Infrared while radio frequency signals can be transmitted even when there is obstacles. Infrared signals will get interfeared by other IR sources but signals on one frequency band in RF will not interfeared by other frequency RF signals. -
The MQ series of gas sensors use a small heater inside with an electro-chemical sensor. They are sensitive for a range of gasses and are used indoors at room temperature. The output is an analog signal and can be read with an analog input of the Arduino. The MQ-2 Gas Sensor module is useful for gas leakage detecting in home and industry. It can detect LPG, i-butane, propane, methane ,alcohol, hydrogen and smoke. -
This module integrates DHT11 sensor and other required components on a small PCB. The DHT11 sensor includes a resistive-type humidity measurement component, an NTC temperature measurement component and a high-performance 8-bit micro controller inside, and provides calibrated digital signal output. It has high reliability and excellent long-term stability, thanks to the exclusive digital signal acquisition technique and temperature & humidity sensing technology. -
he smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at any voltage! That’s right - power the board at 5V and the unit will convert RS232 to 5V TTL. Power the board at 2.8V and the Shifter board will convert RS232 to 2.8V CMOS TTL. Includes two indicator LEDs for TX and RX. Runs from 300bps up to 115200bps. -
D-LINK RJ45 Connector Module Plug RCT-690 These connector plugs are designed to be easily installed with a crimp die and used with 24 AWG solid or stranded conductors. Fully compatible with Cat5e universal twisted-pair wire, these plugs are capable of supporting Cat5e speeds as well. -
Mini HDMI 90 Degree Up Angled FPV to HDMI Male FPC Flat Cable 5cm RCT-689 Connector Type -Mini HDMI Right Angle Connector Type-HDMI Male Straight Cable Length- 5 cm soft -
10 MM EMI EMC Conductive Tape 20 MTR RETPE-36 10 MM EMI EMC Conductive Tape 20 MTR Material – Conductive Cloth Glue type – Conductive Acrylic Adhesive Glue type – 1020MM 50M 0.12MM Adhesive thickness – 0.04±0.008 Adhesive Strength with 180° Peel – > 800g/25mm2 Holding Power – 21440minute Horizontal cloth Anti-resistance – ≤0.050 Glue Anti-resistance – ≤0.060 Temperature range – 10°C-80°C shielding efficiency – 75-1000b Vertical cloth Anti-resistance – ≤0.050
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
