-
Bring oscillation source Audino 9012 drive Work Voltage:3.3V-5V Set bolt hole, easy to assemble PCB Dimension:3.3cm*1.3cm It and your Arduino will be able to play melodies. This is a small buzzer for the Sensor Shield. It creates different sound based on the different frequency of I/O toggling. Pin Definition : Vcc : 3.3V-5V GND : The Ground I/O : I/O Interface of SCM -
The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<->Serial conversion chip and at the end of the 36" cable are four wire - red power, black ground, white RX into USB port, and green TX out of the USB port. The power pin provides the 5V @ 500mA direct from the USB port and the RX/TX pins are 3.3V level for interfacing with the most common 3.3V logic level chip-sets. -
CH340 is a USB bus convert chip and it can realize USB convert to serial interface, USB convert to IrDA infrared or USB convert to printer interface. In serial interface mode, CH340 supplies common MODEM liaison signal, used to enlarge asynchronous serial interface of computer or upgrade the common serial device to USB bus directly. More detail about USB convert to printer interface please referring to the second manual CH340DS2. In infrared mode, add infrared transceiver to CH340 can compose USB infrared adapter, realize SIR infrared communication. -
The MB102 is a breadboard power supply module manufactured by the YuRobot . This module has the marking 545043 and MB V2 on the printed circuit board (PCB). It provides dual 5 V and 3.3 V power rails, and has a multi-purpose female USB socket. -
Just like a joystick on game console. you can control x, y and z dimensions input by this joystick module. It can be considered as combination of potentiometers and one button. Data type of the x, y dimensions are analog input signals and z dimension is digital input signal. thus the x and y ports connect to analog pins of Sensor Shield, while z port connects to digital pin. When using, it can connect with Arduino sensor shield,and connect Arduino corresponding pins through Arduino sensor cables. -
- Drive a 2-phase bipolar stepper motor or two DC motors with the L298 dual H-Bridge chip, mounted on this handy breakout board along with all necessary peripherals!
- It is ideal for robotic applications and well suited for connection to a microcontroller requiring just a couple of control lines per motor. It can also be interfaced with simple manual switches, TTL logic gates, relays, etc.
-
4-channel relay output modules, relay output contacts 250A 10A. Input IN1, IN2, IN3, IN4, the signal line LOW effective. VCC, GND power input, can relay a separate power supply relay power input of JD-VCC. Uses: support all MCU control. the industrial sector PLC control smart home control Wiring: VCC: positive power supply system GND: System power supply negative IN1 - IN4: relay control ports -
Description
This is a 2-Channel Relay interface board, which can control various appliances, and other equipments. It can be controlled directly by Microcontroller. Rated voltage: DC12 Rated current: 10A Coil power: 0.36W Contact switch voltage: 220VAC Protective characteristics: Sealed Contact load: Medium-power Application: Electromagnetism Contact Form: Conversion type With 4 mounting holes, diameter of each hole is 3.1mm, easy to install Apply superior SONGLE relay, SPDT(single-pole double-throw), one common port, one NO and one NC Opto-isolator, excellent anti-interference performance Low level actuation(indicator ON), high level release(indicator OFF) Maximum output of relay: DC 30 -
1.Output Current: 1.5A (min), 2.2A (typ) 2.Input-output voltage differential (VI-VO): 40Vdc (max) 3.Adjustable output voltage range: 1.2 ~ 37V 4.Operating temperature: -55 Celsius ~ 150 Celsius 5.Current output: 1.5A 6.Voltage Input: 4.2 ~ 40 V 7.Operating temperature: 0 Celsius ~ 125 Celsius 8.Characteristic frequency: 100MHz 9.Module size: 35.6 mm x16.8 mm 10.Input Method: VIN input is positive, GND Input Negative 11.Output: VOUT output positive, GND output negative -
Reading Sensing and Controlling current flow is a requirements in a wide variety of application including, over-current protection circuits, switching mode, battery chargers, power supplies, digital watt meter and programmable current source, etc.. The ACS721 current reading module is based on ACS712 Sensor which can detect AC, DC current signal accurately. The maximum AC / DC can be detected using ACS712 will reach 30 amp and present current signal can read via analog IO port of Arduino, Product available for this module are 30A, 20A, 5A. for this demonstration we will used the ACS712 30A.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
SHOP WILL BE CLOSED FROM 21 TO 26 OCTOBER ON THE OCCASION OF DIWALI. COURIERS WON’T BE DISPATCHED OR ATTEND FROM MONDAY 20TH OCTOBER. HAPPY DIWALI…..
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
