-
# Image shown is a representation only #
80MHz 32-bit ARM Cortex-M4-based microcontrollers CPU High Performance TM4C123GH6PM MCU Dual 12-bit 2MSPS ADCs, motion control PWMs -
L6470 is a 3A, 8-45V bipolar stepper motor driver. It has built-in overcurrent detection, undervoltage detection, overtemperature detection, stall detection, a 5-bit ADC, and a switch input that can be used for either user jog control or as a hard stop function. As if that weren’t enough, it also features microstepping support (up to 128 microsteps per full step) and PWM drive voltage limiting. The logic supply voltage supports both 3.3V and 5V I/O levels. -
*FEATURES *Operating Voltage Range: 3V ~ 6.5V *Single Chip, High Quality Audio/Voice Recording & Playback Solution. *No External ICs Required. *Minimum External Components. *User Friendly, Easy to Use Operation. *Programming & Development Systems Not Required. *170/ 340/ 680 sec. Voice Recording Length in aPR33A1/aPR33A2/aPR33A3 *Powerful 16-Bits Digital Audio Processor. *Nonvolatile Flash Memory Technology *No Battery Backup Required. *External Reset pin. *Powerful Power Management Unit *Very Low Standby Current: 1uA *Low Power-Down Current: 15uA *Supports Power-Down Mode for Power Saving. -
Features:- Light weight, small size, easy to install.
- Inlaid with stainless steel impeller shaft, durable wearable.
- Seal ring with the upper and lower force structure never leaks.
- Non-violent shock, and chemical erosion.
- Non-throwing or hitting.
- Mounted vertically, should not exceed 5 degrees inclination.
- Temperature of medium should not exceed 120 ℃.
-
# Image shown is a representation only #
-
The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. Features:- Power supply voltage: VM=15V max, VCC=2.7-5.5V
- Output current: Iout=1.2A(average) / 3.2A (peak)
- Standby control to save power
- CW/CCW/short brake/stop motor control modes
- Built-in thermal shutdown circuit and low voltage detecting circuit
- All pins of the TB6612FNG broken out to 0.1" spaced pins
- Filtering capacitors on both supply lines
-
Dry reed pipe needs and magnet is used together, in the induction to have certain magnetic, a conducting state, module output low level, no magnetic, is off state, output high level, dry reed pipe and magnetic induction distance within in 1.5 cm beyond insensitive or will not trigger phenomenon. Module DO output end of the single chip microcomputer can I/O port directly connected, through the single chip microcomputer can detect dry reed pipe state trigger. Module DO output end and relay IN end connected to form high power dry reed pipe switch, direct control high voltage. -
Features: *Size: 50 x 26 x 15mm (excluding propellers) *Propeller diameter: 75mm *Operating voltage: 5V *L9110 driver can control reversing, with mounting holes, compatible steering rudder control, quality and high efficiency propeller. *Can easily blow out the flame lighters 20m away, can be used for fire fighting robot, it is essential for robot design and development. -
Overview:- Small kit, easy to use .
- The LCD driver board is HDMI/VGA/2AV Reversing Driver board.
- This controller board supports Automatically Switch to AV2(Reversing View camera). Please connected ACC to 12V. Power Supply is NOT included.
- If you want to conect this screen to your Raspberry Pi, you need a AV Cable or a HDMI Cable, or if you have a HDMI TO VGA CABLE for Raspberry pi, you can use a VGA Cable to connect your Raspberry pi to this Screen.
- There is a sticker on the LCD screen. Please peel off before use.
-
This DSO138 digital oscilloscope kit adopts ARM Cortex-M3 processor and with 2.4-inch TFT screen. It's easy and reliable for circuit operation. It can display frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Features:This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board.Can be secondary development on the basis of this kit, for example, it can be changed to Millivoltmeter, data loggers.Adjustable vertical displacement, and with instructions.With automatic, regular and one-shot modes, easy to capture the moment waveform.Available rising or falling edge trigger.Observable previous trigger waveform (negative delay).Can freeze at any time waveform display (HOLD function).Comes 1Hz /3.3V square wave test signal source.With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Waveform storage function: will not lose the waveform after power off.Short-circuit and open-circuit detection: can help the user find out the soldering error.TFT controller recognition function.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
