-
The TSL2561 is an inexpensive, yet sophisticated, light sensor. Unlike simpler sensors, like photoresistors and photodiodes, the TSL2561 incorporates both infrared and visible light sensors to better approximate the response of the human eye. Because the TSL2561 is an integrating sensor (it soaks up light for a predetermined amount of time), it is capable of measuring both very small and very large amounts of light. -
'-The lamp brightness can be adjusted by requirement,it is very to operate. -It can touch in medium protection,such glass,acrylic,plastic,ceramics and so on,which is very safe. -Wide application of voltage range,you can choose arbitrarily between 2.4V to 4.5V. -Anti power and phone interference,the EFT can reach above /-2KV;the touch response sensitivity and reliability will not affected by the close distance or multi-angle mobile phone interference. -Install: Needn’t to touch copper foil directly,the dimming can be processed across acrylic glass(above 3mm) or plastic. -Application:It can control LED module,light and so on.It is available for indoor LED,lighting lamp,DIY automotive lights dimming refit. -Function:Single touch,using the principle of capacitance touch .-The default function is switch,dimming,with brightness memories LED touch dimming.It will light slowly when turn on the lights,and become dark slowly when turn off,which effectively avoid the stimulation to eyes. -Dimming mode:Non-polar PWM dimming. -Wiring method:PCB board(VCC,GND) is power input,(LED , LED-) is connected with the LED lamps of positive and negative level (fingerprint) touch area, also can wire to lead out (the wiring should not be too long), copper skin area should be 2x3cm. With copper foil copper foil board module will side to the shell side. -
OLED Driver IC: SSD1306 Input Voltage: 3.3V ~ 6V Only Need 2 I/O Port to Control # Image shown is a representation only # -
Description: The module is used in chip TM1638, a collection of these three common MCU peripheral circuit, the biggest feature is just take three microcontroller IO port to drive, do not need to scan display and key scanning microcontroller intervention, only need to read the relevant register send display data or test button, save MCU resources. We usually use an external microcontroller 8 LED, 8 digital tube, eight keys which will occupy the number of IO ports, far more than three IO mouth it, but with this module can be achieved. The practical application of key sensitive display good results. Wiring: VCC GND connected to 5V power supply, STB CLK DIO connected microcontroller IO port. -
This shield V03 can achieve a simple two crunodal ZigBee network，achieve wireless communication between Arduino ，and allows the Arduino to wireless communicate over a modified ZigBee protocol using the popular XBee module.It works with all XBee modules including the Series 1 and Series 2.5, standard and Pro versions. -
'-24V 4-Channel Relay interface board, and each one needs 50-60mA Driver Current. -Equipped with high-current relay, AC250V 10A ; DC30V 10A. -Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). -Indication LED’s for Relay output status. -
'-24V 2-Channel Relay interface board, and each one needs 50-60mA Driver Current. -Equipped with high-current relay, AC250V 10A ; DC30V 10A. -Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). -Indication LED’s for Relay output status. -
'-24V 1-Channel Relay interface board, and each one needs 50-60mA Driver Current. -Equipped with high-current relay, AC250V 10A ; DC30V 10A. -Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic). -Indication LED’s for Relay output status. -
This SIM808 all in one Shield is a GSM and GPS Bluetooth all-in-one function module. It is based on the latest GSM/GPS module SIM808 from SIMCOM, supports GSM/GPRS Quad-Band network and combines GPS technology for satellite navigation. It features ultra-low power consumption in sleep mode and integrated with charging circuit for Li-Ion batteries, that make it get a super long standby time and convenient for projects that use rechargeable Li-Ion battery. It has high GPS receive sensitivity with 22 tracking and 66 acquisition receiver channels. Besides, it also supports A-GPS that available for indoor localization. The module is controlled by AT command via UART and supports 3.3V and 5V logical level. The hardware for SIM808 Shield is compatible with the Arduino. -
Specification: -Voltage: 3.3V. -It's for 8 Pin NRF24L01 Module. -A simple socket board which is for NRF24L01 wireless module. -On-board AMS1117-3.3 chip. -It can be used with NRF24L01 wireless module. -Dimension: 26 x 19 x 12mm.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
