-
9-0-9 Center Tapped 1 AMP Step Down Transformer PS-48 Voltage Efficiency- ± 15% Current Efficiency- 65% Input Voltage: 230V AC Output Voltage: 9V, 0V or ground And 9V Output Current: 1 AMP Mounting -Vertical mount type Winding: Copper Stamping-CRNGO Size-48x40x19 mm -
ECG/EKG/EMG Cable Only With Connector E-977 Cord length: 40 cm. 3-lead line: buckle ECG/EMG cable that is 40 cm in length and has a 3.5mm phone jack. -
BFY90 NPN RF Bipolar Transistors TRD-108 Transistor Polarity: NPN Collector- Emitter Voltage VCEO Max 15 V Emitter- Base Voltage VEBO 2.5 V Continuous Collector Current: 25 Ma Operating Frequency 1.1 GHz Package / Case: TO-72 -
Hi-Link HLK-LD2420 24Ghz human body micro motion sensing detection E-982 Power supply: 3.3 V (3.0 V ~ 3.6) Operating Current: 50 mA Band: 24 GHz -
SFH350 Plastic Fiber Optic Phototransistor Detector RSN-176 Voltage DC Reverse Vr Max --30 V Capacitance -21.5Pf Wavelength -850nm Spectral Bandwidth-400nm -
DC To AC Solid State Relay- HDA-480-10A RERL-55 Output-25-480VAC-10 AMP Input-3-32V DC Opto Isolation Voltage – 2500 Vac Zero Current turn off Fast Switching Response Long Life, highly Reliable Instant(Random) turn on for Inductive Load Zero Voltage turn on Built in Snubber No noise feed back from output to input circuits Reverse polarity protection for DC/AC relays -
DC To AC Solid State Relay- HDA-480-16A RERL-56 Output-25-480VAC-16 AMP Input-3-32V DC Opto Isolation Voltage – 2500 Vac Zero Current turn off Fast Switching Response Long Life, highly Reliable Instant(Random) turn on for Inductive Load Zero Voltage turn on Built in Snubber No noise feed back from output to input circuits Reverse polarity protection for DC/AC relays -
0-12 1AMP Step Down Transformer PS-45 Voltage Efficiency- ± 15% Current Efficiency- 65% Input Voltage: 230V AC Output Voltage: 12V, 0V or ground Output Current: 1 AMP Mounting -Vertical mount type -
Sensitive material of MQ-9 gas sensor is SnO2, which with lower conductivity in clean air. It make detection by method of cycle high and low temperature, and detect CO when low temperature (heated by 1.5V). The sensor’s conductivity is more higher along with the gas concentration rising. When high temperature (heated by 5.0V), it detects Methane, Propane etc combustible gas and cleans the other gases adsorbed under low temperature. Please use simple electrocircuit, Convert change of conductivity to correspond output signal of gas concentration. MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application. -
This sensor sits in line with your water line and contains a pinwheel sensor to measure how much liquid has moved through it. There's an integrated magnetic hall effect sensor that outputs an electrical pulse with every revolution. The hall effect sensor is sealed from the water pipe and allows the sensor to stay safe and dry. The sensor comes with three wires: red (5-24VDC power), black (ground) and yellow (Hall effect pulse output). By counting the pulses from the output of the sensor, you can easily calculate water flow. Each pulse is approximately 2.25 milliliters. Note this isn't a precision sensor, and the pulse rate does vary a bit depending on the flow rate, fluid pressure and sensor orientation. It will need careful calibration if better than 10% precision is required. However, its great for basic measurement tasks!
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
