-
*FEATURES *Operating Voltage Range: 3V ~ 6.5V *Single Chip, High Quality Audio/Voice Recording & Playback Solution. *No External ICs Required. *Minimum External Components. *User Friendly, Easy to Use Operation. *Programming & Development Systems Not Required. *170/ 340/ 680 sec. Voice Recording Length in aPR33A1/aPR33A2/aPR33A3 *Powerful 16-Bits Digital Audio Processor. *Nonvolatile Flash Memory Technology *No Battery Backup Required. *External Reset pin. *Powerful Power Management Unit *Very Low Standby Current: 1uA *Low Power-Down Current: 15uA *Supports Power-Down Mode for Power Saving. -
The Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3 CPU. It is the first Arduino board based on a 32-bit ARM core microcontroller. It has 54 digital input/output pins (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UARTs (hardware serial ports), a 84 MHz clock, an USB OTG capable connection, 2 DAC (digital to analog), 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button.Warning: Unlike most Arduino boards, the Arduino Due board runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. -
Arduino IO shield come up with on board motor driver, Buzzer, Indication LEDs and joystick. This board can be directly attached to Arduino UNO, Duemilanove. Features :- On board LEDs.
- On board Motor Driver.
- Direct sensor interface.
- On board Switches.
- On board Joystick.
- On board Buzzer with driver circuit.
- Motor Input/Output connection.
- Attaches directly to Arduino.
-
The Leonardo is Arduino’s first development board to use one microcontroller with built-in USB. Using the ATmega32U4 as its sole microcontroller allows it to be cheaper and simpler. Also, because the 32U4 is handling the USB directly, code libraries are available which allow the board to emulate a computer keyboard, mouse, and more using the USB-HID protocol! It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. -
The Mega 2560 is a microcontroller board based on the ATmega 2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards. -
Supported UART baud-rates-2400,4800,9600,19200,38400,57600,25000 Un-Supported UART baud-rates-115200,230400 Baud Rate For serial monitor should be 9600 and 2400 The Boards are compatible with Arduino IDE 1.6.5 AND 1.8.4# Image shown is a representation only #
-
Arduino Nano is a surface mount breadboard embedded version with integrated USB. It is a smallest, complete, and breadboard friendly. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard 5V AREF jumper. Physically, it is missing power jack. The Nano is automatically sense and switch to the higher potential source of power, there is no need for the power select jumper. Nano’s got the breadboard-ability of the Boarduino and the Mini USB with smaller footprint than either, so users have more breadboard space. It’s got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other). This new version 3.0 comes with ATMEGA328 which offer more programming and data memory space. It is two layers. That make it easier to hack and more affordable. -
This is Arduino running the 16MHz bootloader. Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It’s a great board that will get you up and running quickly. The Arduino Pro series is meant for users that understand the limitations of system voltage , lack of connectors, and USB off board.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
