-
Supports Full and Half-Duplex modes Automatic Programmable Retransmit on Collision Programmable Padding and CRC Generation Automatic Rejection of Erroneous Packets SPI Interface with Clock Speeds Up to 20 MHz The board 25MHZ crystal. The network interface board HR911105A. 5 V power supply pin. Stable performance. For Arduino SPI, AVR, PIC, LPC, STM32.
-
Description This is a great little RFID Reader Module from Innovations, simillar to the ID models (the difference being no silicone protection on the back). If you need an inexpensive way to get started with RFID, this is a great little module. Just power the module, and it will read any RFID card within range. 1. Reading distance : 100mm 2. Frequncy:125Khz 3. Card format : EM4100 or compatible chip It will output the cards ID in a serial string, which can easily be read by any microcontroller. The spacing on the pins is 2.54 mm, which means the module will directly fit on a breadboard.Note: This Module will not work the Atmega32u2 Developement Board. Technical Specifications 1. 5V supply 2. 125kHz read frequency 3. EM4001 64-bit RFID tag compatible 4. 9600bps TTL and RS232 output 5. Magnetic stripe emulation output 6. 100mm read range 7. Interface: Wiegand 26 , RS232 8. Output: RS232 and WG26 9. Range of power supply: 4.6V to 5.4V 10.Encoding: Manchester 64-bit,modulus 64
-
This sensor takes a continuous reading of any obstacle and settles it at output in TTL form within 2ms. The sensor provides easy interface of 3-wire with power, ground and the output voltage. The sensor works on 5V input Features -Very Small in size -Less influence on the color of reflected objects, reflectivity -Industrial grade quality -Can detect colour difference from certain range -TTL output high whenever sensor senses a obstacle -Detecting distance of 3cm to 80cm -External control circuit unnecessary -Low cost -Has inbuilt lenses assembly and potentiometer to set range of the module -Output indication LED
-
Dynamo Hand Crank Charger E-874 Maximum Output Voltage: DC5.5V/Maximum Output Current: 600mA/Interface type: USB It is better than a solar charger because you can use it even without the heat of the sun It is great for emergency situations, for trekking, fishing, camping, mountain climbing, and even just for everyday use
-
Features: Kits using ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display can be used as ARM test development board. Available source, Capable people can be secondary development on the basis of the suite, for example, it can be changed to Millivoltmeter, data loggers, and so on (we don't supply any technical support about that). Circuit is simple and the kit is inexpensive Description: PCB size: 117 x 76mm Screen size: 52 x 40mm Supply voltage: DC 9V
-
This DSO138 digital oscilloscope kit adopts ARM Cortex-M3 processor and with 2.4-inch TFT screen. It's easy and reliable for circuit operation. It can display frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Features:This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board.Can be secondary development on the basis of this kit, for example, it can be changed to Millivoltmeter, data loggers.Adjustable vertical displacement, and with instructions.With automatic, regular and one-shot modes, easy to capture the moment waveform.Available rising or falling edge trigger.Observable previous trigger waveform (negative delay).Can freeze at any time waveform display (HOLD function).Comes 1Hz /3.3V square wave test signal source.With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Waveform storage function: will not lose the waveform after power off.Short-circuit and open-circuit detection: can help the user find out the soldering error.TFT controller recognition function.
-
It is a durable probe essential for outdoor use. This also comes with a green LED for directing users where to touch. The probe comes with a brass M18 x 1 nut for panel mounting. Since the body of the probe also forms the ground contact, the panel should be of non-conducting material to avoid ground loops. The 30cm cable with connector is provided for easy connection to the system microcontroller.
-
General Description The DS3231 is a low-cost, extremely accurate I2C real-time clock (RTC) with an integrated temperaturecompensated crystal oscillator (TCXO) and crystal. The device incorporates a battery input, and maintains accurate timekeeping when main power to the device is interrupted. The integration of the crystal resonator enhances the long-term accuracy of the device as well as reduces the piece-part count in a manufacturing line. The DS3231 is available in commercial and industrial temperature ranges, and is offered in a 16-pin, 300-mil SMD package.
-
Cable specs: -Stainless steel tube 6mm diameter by 30mm long. -Cable is 36" long / 91cm, 4mm diameter. -Contains DS18B20 temperature sensor. -If your sensor has four wires - Red connects to 3-5V, Black connects to ground and White is data. The copper wire is soldered to the wire shielding. -If your sensor has three wires - Red connects to 3-5V, -Blue/Black connects to ground and Yellow/White is data. DS18B20 Technical specs: -Usable temperature range: -55 to 125°C (-67°F to 257°F). -9 to 12 bit selectable resolution. -Uses 1-Wire interface- requires only one digital pin for communication. -Unique 64 bit ID burned into chip. -Multiple sensors can share one pin. ±0.5°C Accuracy from -10°C to 85°C. -Temperature-limit alarm system. -Query time is less than 750ms. -Usable with 3.0V to 5.5V power/data.