-
The MPX5010DP is a dual port, integrated silicon pressure sensor in 6 pin SIP package. This piezoresistive transducer is state of the art monolithic silicon pressure sensor designed for wide range of applications. It is ideally suited for microprocessor or microcontroller based system. This transducer combines advanced micromachining techniques, thin-film metallization and bipolar processing to provide an accurate, high level analogue output signal that is proportional to applied pressure. The axial port has been modified to accommodate industrial grade tubing. >On-chip signal conditioned, temperature compensated and calibrated >Differential configuration >5.0% maximum error over 0°C to 85°C >Durable epoxy unibody >Temperature compensated over -40°C to 125°C >Patented silicon shear stress strain gauge >Pressure range from 0KPa to 10KPa >Supply voltage range from 4.75VDC to 5.25VDC >Sensitivity of 450mV/mm >Response time of 1ms
-
This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
-
This Arduino shield from Adafruit features TI’s CC3000 Wi-Fi module with an onboard ceramic antenna, a microSD card socket, and a designated prototyping area. The CC3000 uses SPI for communication instead of UART, so the communication speed is not limited to a fixed baud rate. It supports 802.11b/g, open/WEP/WPA/WPA2 security, TKIP, and AES, and a built-in TCP/IP stack with a BSD socket interface supports TCP and UDP in client and server mode with up to 4 concurrent socket connections.
-
Description: The GPRS Shield is based on SIM900 module from SIMCOM and compatible with Arduino and its clones. The GPRS Shield provides you a way to communicate using the GSM cell phone network. The shield allows you to achieve SMS, MMS, GPRS and Audio via UART by sending AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands). The shield also has the 12 GPIOs, 2 PWMs and an ADC of the SIM900 module(They are all 2V8 logic) present onboard.
-
Yun Shield runs Open Source OpenWrt system and it is fully compatible with Arduino IDE v1.5.4 or later. Yun Shield is the ideally choice for Arduino Projects w Yun Shield is one of the most powerful shields for Arduino Board. Yun Shield is designed to solve the Internet connectivity and storage issue for Arduino Board. Yun Shield runs Open Source OpenWrt system (Same system as runs in Arduino Yun) and it is fully compatible with Arduino IDE v1.5.4 or later. Yun Shield is the ideally choice for Arduino Projects which require various internet connections and more storage.
-
The MPX2010DP is a differential, dual port silicon pressure sensor in 4 pin SIP package. This piezoresistive pressure sensor provides very accurate and linear voltage output directly proportional to applied pressure. It includes on-chip integrated strain gauge and thin film resistor network. The sensor is laser trimmed for precise span, offset calibration and temperature compensation.
-
Q2406 Wavecom GSM Modem with USB for Arduino/Raspberry-Pi/Robotics The Q2406 wavecom GSM modem follows plug and play operation with on board USB interface for communication and follows standard AT command set. Advantage of using this modem will be that you can use its USB port to communicate and develop embedded applications. The modem can either be connected to PC serial port directly or to any microcontroller. It can also be used in GPRS mode to connect to internet and do many applications for data logging and control. Features of Q2406 Wavecom GSM Modem with USB: Dual Band EGSM/GPRS 900/1800 MHz. Compliant to GSM phase 2. GPRS Class 2. Output power: Class4 2W for EGSM 900. Class2 1W for GSM1800. Control via AT commands. SIM application tool kit. Supply voltage range: 3.1 to 4.5VDC. Temperature range: -20 to 55 (operational functionality). -30 to 85 (storage temperature). Dimensions: 58.3x 32.2x 3.9mm. Weight: 17g. Voice: noise suppression and echo cancellation. SMS: Text and PDU mode, Point to point (MO/MT), Cell broadcast. DATA: Transparent and non transparent CSD up to 9.6kbps, USSD,. Interfaces: RF connector, 60 pin system connector,. SIM card connector, keypad and LCD etc.. Applications of Q2406 Wavecom GSM Modem with USB: Large shopping malls, supermarkets. Professional market, large wholesalers. Large hotels, large-scale entertainment. Large agencies. Transport, logistics industry. Large enterprises, and institutions. Large hospitals, large bookstore. Newspaper, television and radio stations. Oil Company (other chain business model). Government agencies or large township. These are used in different robotics applications. GSM based Electrical/Electronic project.
-
This is the XBee XBP24-BZ7WIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. Series 2B modules use a different hardware configuration from the earlier models and while they will communicate with Series 2 XBee modules, they are not compatible with the outdated Series 2.5 Modules.