-
BeagleBone Black is a low-cost, community-supported development platform for developers and hobbyists. Boot Linux in under 10 seconds and get started on development in less than 5 minutes with just a single USB cable. Processor: AM335x 1GHz ARM® Cortex-A8 512MB DDR3 RAM 4GB 8-bit eMMC on-board flash storage 3D graphics accelerator NEON floating-point accelerator 2x PRU 32-bit microcontrollers
-
This shield V03 can achieve a simple two crunodal ZigBee network,achieve wireless communication between Arduino ,and allows the Arduino to wireless communicate over a modified ZigBee protocol using the popular XBee module.It works with all XBee modules including the Series 1 and Series 2.5, standard and Pro versions.
-
The BMP180 Breakout is a barometric pressure sensor with an I2C (“Wire”) interface. Barometric pressure sensors measure the absolute pressure of the air around them. This pressure varies with both the weather and altitude. Depending on how you interpret the data, you can monitor changes in the weather, measure altitude, or any other tasks that require an accurate pressure reading.
-
The BMP280 sensor is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI. Features: - Pressure range: 300 ~ 1100hPa (altitude 9000 m ~ -500 m); - Working voltage: 1.71 - 3.6VDC; - Low power consumption: 4μA; - High precision: at low-power mode, the resolution is 0.06hPa (0.5 meters); - Temperature output; - Communication interface: I2C or SPI; typical application: - GPS precise navigation (dead reckoning, the upper and lower bridge detection, etc.); - indoor and outdoor navigation; - The weather forecast; - The vertical velocity indication (rise / sink speed);
-
The CC2500 is a low-cost 2.4 GHz transceiver designed for very low-power wireless applications. The circuit is intended for the 2400- 2483.5 MHz ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency band. The RF transceiver is integrated with a highly configurable base-band modem. The modem supports various modulation formats and has a configurable data rate up to 500 kBaud. CC2500 provides extensive hardware support for packet handling, data buffering, burst transmissions, clear channel assessment, link quality indication, and wake-on-radio.
-
This High Speed CC2500 Based Wireless module is a plug and play replacement for the wired Serial Port (UART) supporting baud rates upto 38400. This CC2500 based Wireless module allow engineers of all skill levels to quickly and cost-effectively add wireless capabilities to virtually any product. More details and tutorials of this module are available in the resources section. It is not compatible with older RFpro modules.
-
- Supports Multiple Baud rates (4800/9600/19200/38400).
- Works on ISM band (2.4 GHz) which is reserved internationally so no need to apply for license.
- No complex wireless connection software or intimate knowledge of RF is required to connect your serial devices.
- Designed to be as easy to use as cables.
- No external Antenna required.
- Plug and play device.
- Works on 5-9v DC supply.
- Standard UART Interface.
-
This Arduino shield from Adafruit features TI’s CC3000 Wi-Fi module with an onboard ceramic antenna, a microSD card socket, and a designated prototyping area. The CC3000 uses SPI for communication instead of UART, so the communication speed is not limited to a fixed baud rate. It supports 802.11b/g, open/WEP/WPA/WPA2 security, TKIP, and AES, and a built-in TCP/IP stack with a BSD socket interface supports TCP and UDP in client and server mode with up to 4 concurrent socket connections.
-
CH340 is a USB bus convert chip and it can realize USB convert to serial interface, USB convert to IrDA infrared or USB convert to printer interface. In serial interface mode, CH340 supplies common MODEM liaison signal, used to enlarge asynchronous serial interface of computer or upgrade the common serial device to USB bus directly. More detail about USB convert to printer interface please referring to the second manual CH340DS2. In infrared mode, add infrared transceiver to CH340 can compose USB infrared adapter, realize SIR infrared communication.