-
Overview:- Small kit, easy to use .
- The LCD driver board is HDMI/VGA/2AV Reversing Driver board.
- This controller board supports Automatically Switch to AV2(Reversing View camera). Please connected ACC to 12V. Power Supply is NOT included.
- If you want to conect this screen to your Raspberry Pi, you need a AV Cable or a HDMI Cable, or if you have a HDMI TO VGA CABLE for Raspberry pi, you can use a VGA Cable to connect your Raspberry pi to this Screen.
- There is a sticker on the LCD screen. Please peel off before use.
-
This DSO138 digital oscilloscope kit adopts ARM Cortex-M3 processor and with 2.4-inch TFT screen. It's easy and reliable for circuit operation. It can display frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Features:This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen, can be used as ARM test development board.Can be secondary development on the basis of this kit, for example, it can be changed to Millivoltmeter, data loggers.Adjustable vertical displacement, and with instructions.With automatic, regular and one-shot modes, easy to capture the moment waveform.Available rising or falling edge trigger.Observable previous trigger waveform (negative delay).Can freeze at any time waveform display (HOLD function).Comes 1Hz /3.3V square wave test signal source.With waveform parameter digital display, including frequency, period, pulse width, duty ratio, MAX./MIN./AVG./Peak-Peak/virtual values.Waveform storage function: will not lose the waveform after power off.Short-circuit and open-circuit detection: can help the user find out the soldering error.TFT controller recognition function. -
Features: Kits using ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display can be used as ARM test development board. Available source, Capable people can be secondary development on the basis of the suite, for example, it can be changed to Millivoltmeter, data loggers, and so on (we don't supply any technical support about that). Circuit is simple and the kit is inexpensive Description: PCB size: 117 x 76mm Screen size: 52 x 40mm Supply voltage: DC 9V -
Description: -Brand new Black/White Line Hunting Sensor for Intelligent Car Tracing. -Features VCC/OUT/GND pin connector. -Output electrical level signal: Low level when detecting objects/ high level when no objects/0 or 1 decides if objects exist. -Power by 2.5-12V (cannot over 12V). -Perfect DIY parts for intelligent cars. -Color: Black panel -Working Current: 18-20mA at 5V -Package Dimensions: 77.0 x 49.0 x 12.0 mm -Weight: 5.0g -
The BMP280 sensor is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI. Features: - Pressure range: 300 ~ 1100hPa (altitude 9000 m ~ -500 m); - Working voltage: 1.71 - 3.6VDC; - Low power consumption: 4μA; - High precision: at low-power mode, the resolution is 0.06hPa (0.5 meters); - Temperature output; - Communication interface: I2C or SPI; typical application: - GPS precise navigation (dead reckoning, the upper and lower bridge detection, etc.); - indoor and outdoor navigation; - The weather forecast; - The vertical velocity indication (rise / sink speed); -
W5500 Ethernet shield is designed using the WIZnet W5500 chip. It supports both 3.3V & 5V. This Ethernet Shield is compatible with Arduino and ARM embed Platform. Features -Suppport 3.3V / 5V. -High Speed Ethernet controller W5500 chip. -SPI interface. -Internal 32Kbytes Tx/Rx buffer. -10/100 Ethernet PHY embedded. -Support Auto Negotiation (Full / Half duplex, 10 / 100-based). -Hardwired TCP/IP Protocols : TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE. -User Selectable GPIO pin. -Support SD-card slot for storage. -Support I2C, UART interface. -
Naze32 6DOF Flight Control Board E-471 tem Type: Flight Controller Model: Naze32 6DOF Input Voltage (V): 3.3V~5V DC Firmware: Naze Firmware Sensor: MPU6500 / Processor: STM32 F103 Micro SD Card Slot (Y/N): No -
Feature: *Operating voltage: 5V. *On-board MAX485 chip. *A low power consumption for the RS-485 communication. *Slew-rate limited transceiver. *5.08mm pitch 2P terminal. *Convenient RS-485 communication wiring. *All pins of chip have been lead to can be controlled through the microcontroller. *Board size: 44 x 14mm.
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
