-
RP2040 microcontroller with 2MB of flash memory On-board single-band 2.4GHz wireless interfaces (802.11n) Micro USB B port for power and data (and for reprogramming the flash) 40 pin 21mmx51mm ‘DIP’ style 1mm thick PCB Exposes 26 multi-function 3.3V general purpose I/O (GPIO) 23 GPIO are digital-only, with three also being ADC capable -
he Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 (Atmega8U2 up to version R2) programmed as a USB-to-serial converter. Revision 2 of the Uno board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode. -
This High Speed CC2500 Based Wireless module is a plug and play replacement for the wired Serial Port (UART) supporting baud rates upto 38400. This CC2500 based Wireless module allow engineers of all skill levels to quickly and cost-effectively add wireless capabilities to virtually any product. More details and tutorials of this module are available in the resources section. It is not compatible with older RFpro modules. -
Operating temperature -30 to 80 Operating Voltage 3.3V-4.2V Power Voltage 3.4V Standby average current 3ma the following Stand by GSM / GPRS Four bands, including 850,900,1800,1900MHZ GPRS Class 10 Sensitivity -105 Support voice calls Stand by SMS SMS Stand by GPRS Data services, the maximum data rate, downloads 85.6Kbps, Upload 42.8Kbps Supports standard GSM07.07,07.05 AT Command and Ai Thinker Extended Command Stand by 2 A serial port, a serial port to download, a AT Command port AT Command supports standard AT and TCP / IP Command interface It supports digital audio and analog audio support HR , FR , EFR , AMR Speech coding Stand by ROHS , FCC , CE , CTA Certification SMT 42PIN Packaging -
4 Channel Wireless RF Remote Module 433Mhz- The super-regenerative receiver module using the LC oscillator circuit containing amplifier shaping, the output data signal is decoded. Receiver module has a wide receiver bandwidth, typically ± 10MHz, factory general tone in the 433.92MHZ. The receiver module is DC 5V power supply. Specifications:- Operating voltage (V): DC5V
- Quiescent Current (mA): 4.5MA
- Modulation: AM (OOK)
- Operating Temperature: -10 ° C to 70 ° C
- Receiver sensitivity (dBm):-105DB
- Operating frequency (MHz): 433.92 MHz
- Encoding: the pad code (fixed code)
- Work: M4 - Jog: Press and hold let go on the output, let go to stop the output
- Dimensions (LWH): 41 x 23 * 7mm
-
SOP28 to DIP28 28 pin IC socket will convert SOP28 into DIP28, SOP28 / SOIC28 / SO28 IC Programmer Adapter is 1.27 mm Pitch and 7.5 mm Width, SOP28 8 pin programmer adapter. SOP28 to DIP28 28 pin IC socket SOIC28 IC adapter. Features: 1. CNV SOP28、SOIC28、SO28 28 pin ic socket 2. Tested before shipping 3. Easy to use -
The TB6560-3 Axis Stepper Motor Driver is a excellent microstepping driver that use TOSHIBA TB6560 Chip,based on pure-sine current control technology.Owing to the above technology and the self-adjustment technology (self-adjust current control parameters) according to different motors, the driven motors can run with smaller noise, lower heating, smoother movement and have better performances at higher speed than most of the drives in the markets. It is suitable for driving 2-phase and 4-phase hybrid stepping motors. -
Input voltage: 5-40V;Output voltage: 1.2-30V adjustable，1.2-30V fixed output Output Current: 12A MAX (rated 8A, peak 12A) 100W enhance heat dissipation of up to 200W,Working temperature: -40 to 85 degrees Operating frequency: 180KHz;Conversion efficiency: up to 95% Short circuit protection: Yes (limit current 12A) Overtemperature protection: (automatically shut off the output after overtemperature) Input Reverse Polarity Protection: None Installation: four 3mm screws (not included) Connection: terminals, solderless, V-IN is the input, V-OUT is the output, with wire output module housing. Module size: 50mm * 50mm * 18mm Application: This module can be used in batteries, power transformers, DIY adjustable power supply, 24V car T of the power supply, automotive LED lights with power, industrial Buck equipment, 12V t- 3.3V, 12V - 5V, 24V - 5V , 24V -12V, etc. Package Included：1 x Buck Converter Module Note:Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is /- 1-3 cm. -
Mini-size RS232 DB9 female port to RS485 DB9 male connector Hot-swappable and plug & play, port-powered over RS232 RS485 The range of baud rate: 300bps-115.2Kbps Working Mode: asynchronous half-duplex (RS485) -
# Image shown is a representation only #
Working voltage : DC 5V Acoustic emission frequency : 40KHz Wiring : +5V (positive) Trig-(control) Echo-(receive) GND-(cathode) -
ESP32-WROOM -32D DevKitC Module WiFi Bluetooth 2.4GHz With Type C Manufacturer Part No: ESP32-DevKitC-32D Manufacturer: Espressif Flash Memory Capacity: 4MB Frequency: 2.4 GHz to 2.5 GHz Operating Supply Voltage: 5V -
Operating Voltage: 3V~6V DC Gear Ratio 1:48 Size: 70 x 23 x 18 mm# Image shown is a representation only #
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
YOUR PARTNER IN TECHNOLOGY SOLUTIONS
No.1030, Shriram Building,
Near Nagnath Par,
Sadashiv Peth, Pune – 411030,
Maharashtra, India
Visit Our store
STORE TIMINGS
Monday to Saturday
10:00 AM to 7.30 PM
(Store closed on all Sundays and Public Holidays)
NOTE
*All the prices are excluding Tax rates & are subject to change after a specific period of time.
Copyright © 2024@AbhinavDCS
